LPC3180FEL320 NXP Semiconductors, LPC3180FEL320 Datasheet - Page 20

• Manufacturer Part Number: LPC3180FEL320
• Description: IC ARM9 MCU 208MHZ 320-LFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC3000r

Specifications of LPC3180FEL320

• Core Size: 16/32-Bit
• Oscillator Type: External
• Core Processor: ARM9
• Speed: 208MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, UART/USART, USB OTG
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 55
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.1 V ~ 3.3 V
• Data Converters: A/D 3x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 320-LFBGA
• No. Of I/o's: 55
• Ram Memory Size: 64KB
• Cpu Speed: 208MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 2
• Digital Ic Case Style: LFBGA
• Supply Voltage Range: 1.7V
• Controller Family/series: LPC31xx
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1018 - EVAL KIT FOR LP3180568-4063 - KIT DEV LPC3180568-4062 - DEBUGGER J-LINK JTAG568-4061 - DEBUGGER U-LINK2 JTAG FOR NXP
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-3242

NXP Semiconductors
LPC3180_2
Preliminary data sheet
6.12.3.1 Features
6.13.1.1 Features
6.12.3 USB OTG Controller
6.13.1 Standard UARTs
6.13.2 High-speed UARTs
6.13 UARTs
USB OTG (On-The-Go) is a supplement to the USB 2.0 specification that augments the
capability of existing mobile devices and USB peripherals by adding host functionality for
connection to USB peripherals.
The LPC3180 contains seven UARTs. Four are standard UARTs, and three are special
purpose high-speed UARTs.
The four standard UARTs are downwards compatible with the INS16Cx50. These UARTs
support rates up to 460800 bit/s from a 13 MHz peripheral clock.
The three high-speed UARTs are designed to support rates up to 921600 bit/s from a
13 MHz peripheral clock, for on-board communication in low noise conditions. This is
accomplished by changing the oversampling from 16 to 14 , and altering the rate
generation logic.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fully compliant with On-The-Go supplement to the USB Specification 2.0 Revision
1.0.
Supports Host Negotiation Protocol (HNP) and Session Request Protocol (SRP) for
dual-role devices under software control. HNP is partially implemented in hardware.
Provides programmable timers required for HNP and SRP.
Supports slave mode operation through AHB slave interface.
Supports the OTG ATX from NXP (ISP 1301) or any external CEA-2011OTG
specification compliant ATX.
Each standard UART has 64 byte Receive and Transmit FIFOs.
Receiver FIFO trigger points at 16 B, 32 B, 48 B, and 60 B.
Transmitter FIFO trigger points at 0 B, 4 B, 8 B, and 16 B.
Register locations conform to 16C550 industry standard.
Each standard UART has a fractional rate pre-divider and an internal baud rate
generator.
The standard UARTs support three clocking modes: on, off, and auto-clock. The
auto-clock mode shuts off the clock to the UART when it is idle.
UART 6 includes an IrDA mode to support infrared communication.
The standard UARTs are designed to support data rates of (2400, 4800, 9600,
19200, 38400, 57600, 115200, 230400, 460800) bit/s.
Each UART includes an internal loopback mode.
Rev. 02 — 15 February 2007
16/32-bit ARM microcontroller with external memory interface
LPC3180
© NXP B.V. 2007. All rights reserved.
20 of 36