ST7FLITEU05M3TR STMicroelectronics, ST7FLITEU05M3TR Datasheet - Page 21

no-image

ST7FLITEU05M3TR

Manufacturer Part Number
ST7FLITEU05M3TR
Description
IC MCU 8BIT 2K FLASH 8SOIC
Manufacturer
STMicroelectronics
Series
ST7r
Datasheet

Specifications of ST7FLITEU05M3TR

Core Processor
ST7
Core Size
8-Bit
Speed
8MHz
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
5
Program Memory Size
2KB (2K x 8)
Program Memory Type
FLASH
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
8-SOIC (3.9mm Width)
Processor Series
ST7FLITEUx
Core
ST7
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
ICC
Maximum Clock Frequency
4 MHz
Number Of Programmable I/os
5
Number Of Timers
2
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Development Tools By Supplier
ST7FUS-PRIMER, ST7FLITE-SK/RAIS, ST7FLITU0-D/RAIS, STX-RLINK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 5 Channel
For Use With
497-5858 - EVAL BOARD PLAYBACK ST7FLITE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
 Details
ST7LITEU05 ST7LITEU09
Caution:
4.5
4.5.1
4.5.2
3. The use of Pin 7 of the ICC connector depends on the programming tool architecture. This pin must be
4. Pin 9 has to be connected to the CLKIN pin of the ST7 when ICC mode is selected with option bytes
5. A serial resistor must be connected to ICC connector pin 6 in order to prevent contention on PA3/RESET
During normal operation, ICCCLK pin must be pulled- up, internally or externally (external
pull-up of 10k mandatory in noisy environment). This is to avoid entering ICC mode
unexpectedly during a reset. In the application, even if the pin is configured as output, any
reset will put it back in input pull-up.
Memory protection
There are two different types of memory protection: readout protection and write/erase
protection which can be applied individually.
Readout protection
Readout protection, when selected provides a protection against program memory content
extraction and against write access to Flash memory. Even if no protection can be
considered as totally unbreakable, the feature provides a very high level of protection for a
general purpose microcontroller. Program memory is protected.
In Flash devices, this protection is removed by reprogramming the option. In this case,
program memory is automatically erased, and the device can be reprogrammed.
Readout protection selection depends on the device type:
Flash write/erase protection
Write/erase protection, when set, makes it impossible to both overwrite and erase program
memory. Its purpose is to provide advanced security to applications and prevent any change
being made to the memory content.
Write/erase protection is enabled through the FMP_W bit in the option byte.
ensure that no external reset is generated by the application during the ICC session.
connected when using most ST programming tools (it is used to monitor the application power supply).
Please refer to the programming tool manual.
disabled (35-pulse ICC entry mode). When option bytes are enabled (38-pulse ICC entry mode), the
internal RC clock is forced, regardless of the selection in the option byte.
pin. Contention may occur if a tool forces a state on RESET pin while PA3 pin forces the opposite state in
output mode. The resistor value is defined to limit the current below 2 mA at 5 V. If PA3 is used as output
push-pull, then the application must be switched off to allow the tool to take control of the RESET pin
(PA3). To allow the programming tool to drive the RESET pin below V
when a pull-up is placed on PA3 for application reasons.
In Flash devices it is enabled and removed through the FMP_R bit in the option byte.
In ROM devices it is enabled by mask option specified in the option list.
Warning:
Once set, Write/erase protection can never be removed. A
write-protected flash device is no longer reprogrammable.
IL
, special care must also be taken
Flash program memory
21/139

Related parts for ST7FLITEU05M3TR