Z8F0113PJ005SG Zilog, Z8F0113PJ005SG Datasheet - Page 166
Z8F0113PJ005SG
Manufacturer Part Number
Z8F0113PJ005SG
Description
IC ENCORE MCU FLASH 1K 28DIP
Manufacturer
Zilog
Series
Encore!® XP®r
Datasheet
1.Z8F0223SB005SG.pdf
(247 pages)
Specifications of Z8F0113PJ005SG
Core Processor
Z8
Core Size
8-Bit
Speed
5MHz
Connectivity
IrDA, UART/USART
Peripherals
Brown-out Detect/Reset, LED, POR, PWM, WDT
Number Of I /o
24
Program Memory Size
1KB (1K x 8)
Program Memory Type
FLASH
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
28-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Other names
269-3995
Z8F0113PJ005SG
Z8F0113PJ005SG
- Current page: 166 of 247
- Download datasheet (4Mb)
PS024314-0308
OCD Unlock Sequence (8-Pin Devices Only)
Breakpoints
Runtime Counter
Because of pin-sharing on the 8-pin device, an unlock sequence must be performed to
access the DBG pin. If this sequence is not completed during a system reset, then the PA0/
DBG pin functions only as a GPIO pin.
The following sequence unlocks the DBG pin:
1. Hold PA2/RESET Low.
2. Wait 5 ms for the internal reset sequence to complete.
3. Send the following bytes serially to the debug pin:
4. Release PA2/RESET. The PA0/DBG pin is now identical in function to that of the
Execution breakpoints are generated using the
eZ8 CPU decodes a
OCD enters DEBUG mode and idles the eZ8 CPU. If breakpoints are not enabled, the
OCD ignores the BRK signal and the
Breakpoints in Flash Memory
The
byte in Flash memory. To implement a breakpoint, write
address, overwriting the current instruction. To remove a breakpoint, the corresponding
page of Flash memory must be erased and reprogrammed with the original data.
The OCD contains a 16-bit Runtime Counter. It counts system clock cycles between
breakpoints. The counter starts counting when the OCD leaves DEBUG mode and stops
counting when it enters DEBUG mode again or when it reaches the maximum count of
FFFFH
DBG
DBG
DBG
DBG
DBG
DBG pin on the 20- or 28-pin device. To enter DEBUG mode, re-autobaud and write
80H
BRK
.
←
←
←
←
←
to the OCD control register (see
instruction is opcode
80H (autobaud)
EBH
5AH
70H
CDH (32-bit unlock key)
BRK
instruction, it signals the OCD. If breakpoints are enabled, the
00H
, which corresponds to the fully programmed state of a
BRK
On-Chip Debugger Commands
instruction operates as an
BRK
instruction (opcode
Z8 Encore! XP
00H
to the required break
Product Specification
NOP
00H
®
On-Chip Debugger
instruction.
on page 157).
F0823 Series
). When the
156
Related parts for Z8F0113PJ005SG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: