C8051F305-GMR Silicon Laboratories Inc, C8051F305-GMR Datasheet - Page 116

• Manufacturer Part Number: C8051F305-GMR
• Description: IC 8051 MCU 2K FLASH 11QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F30xr

Specifications of C8051F305-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 8
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 11-VQFN
• For Use With: 336-1444 - ADAPTER PROGRAM TOOLSTICK F300
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -

C8051F300/1/2/3/4/5
13.4.1. SMBus Configuration Register
The SMBus Configuration register (SMB0CF) is used to enable the SMBus Master and/or Slave modes,
select the SMBus clock source, and select the SMBus timing and timeout options. When the ENSMB bit is
set, the SMBus is enabled for all master and slave events. Slave events may be disabled by setting the
INH bit. With slave events inhibited, the SMBus interface will still monitor the SCL and SDA pins; however,
the interface will NACK all received addresses and will not generate any slave interrupts. When the INH bit
is set, all slave events will be inhibited following the next START (interrupts will continue for the duration of
the current transfer).
The SMBCS1-0 bits select the SMBus clock source, which is used only when operating as a master or
when the Free Timeout detection is enabled. When operating as a master, overflows from the selected
source determine the absolute minimum SCL low and high times as defined in Equation 13.1. Note that the
selected clock source may be shared by other peripherals so long as the timer is left running at all times.
For example, Timer 1 overflows may generate the SMBus and UART baud rates simultaneously. Timer
configuration is covered in
The selected clock source should be configured to establish the minimum SCL High and Low times as per
Equation 13.1. When the interface is operating as a master (and SCL is not driven or extended by any
other devices on the bus), the typical SMBus bit rate is approximated by Equation 13.2.
Figure 13.4 shows the typical SCL generation described by Equation 13.2. Notice that T
twice as large as T
extended low by slower slave devices, or driven low by contending master devices). The bit rate when
operating as a master will never exceed the limits defined by equation Equation 13.1.
116
LOW
Equation 13.1. Minimum SCL High and Low Times
. The actual SCL output may vary due to other devices on the bus (SCL may be
SMBCS1
Table 13.1. SMBus Clock Source Selection
Section “15. Timers” on page
T
Equation 13.2. Typical SMBus Bit Rate
HighMin
0
0
1
1
BitRate
SMBCS0
=
T
0
1
0
1
LowMin
=
f
--------------------------------------------- -
Rev. 2.9
Timer 1 Overflow
Timer 2 High Byte Overflow
Timer 2 Low Byte Overflow
Timer 0 Overflow
ClockSourceOverflow
=
SMBus Clock Source
--------------------------------------------- -
f
ClockSourceOverflow
3
143.
1
HIGH
is typically