C8051F006-GQR Silicon Laboratories Inc, C8051F006-GQR Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F006-GQR
Manufacturer Part Number
C8051F006-GQR
Description
IC 8051 MCU 32K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F00xr
Specifications of C8051F006-GQR
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
2.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x12b, D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP, 48-VQFP
For Use With
336-1188 - DEV KIT FOR F005/006/007
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F006-GQR
Manufacturer:
SILICON
Quantity:
1 200
Company:
Part Number:
C8051F006-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
5. ADC (12-Bit, C8051F000/1/2/5/6/7 Only)
The ADC subsystem for the C8051F000/1/2/5/6/7 consists of a 9-channel, configurable analog multiplexer
(AMUX), a programmable gain amplifier (PGA), and a 100ksps, 12-bit successive-approximation-register ADC
with integrated track-and-hold and programmable window detector (see block diagram in Figure 5.1). The AMUX,
PGA, Data Conversion Modes, and Window Detector are all configurable under software control via the Special
Function Register’s shown in Figure 5.1. The ADC subsystem (ADC, track-and-hold and PGA) is enabled only
when the ADCEN bit in the ADC Control register (ADC0CN, Figure 5.7) is set to 1. The ADC subsystem is in low
power shutdown when this bit is 0. The Bias Enable bit (BIASE) in the REF0CN register (see Figure 9.2) must be
set to 1 in order to supply bias to the ADC.
5.1.
Eight of the AMUX channels are available for external measurements while the ninth channel is internally
connected to an on-board temperature sensor (temperature transfer function is shown in Figure 5.3). Note that the
PGA gain is applied to the temperature sensor reading. AMUX input pairs can be programmed to operate in either
the differential or single-ended mode. This allows the user to select the best measurement technique for each input
channel, and even accommodates mode changes “on-the-fly”. The AMUX defaults to all single-ended inputs upon
reset. There are two registers associated with the AMUX: the Channel Selection register AMX0SL (Figure 5.5),
and the Configuration register AMX0CF (Figure 5.4). The table in Figure 5.5 shows AMUX functionality by
channel for each possible configuration. The PGA amplifies the AMUX output signal by an amount determined by
the AMPGN2-0 bits in the ADC Configuration register, ADC0CF (Figure 5.6). The PGA can be software-
programmed for gains of 0.5, 1, 2, 4, 8 or 16. It defaults to unity gain on reset.
29
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
Analog Multiplexer and PGA
SENSOR
AGND
TEMP
AMX0CF
ADC0GTH
Figure 5.1. 12-Bit ADC Functional Block Diagram
+
+
+
+
-
-
-
-
AMUX
(SE or
9-to-1
DIFF)
AMX0SL
ADC0GTL
X
+
-
AV+
ADCEN
Rev. 1.7
AGND
ADC0CF
ADC0LTH
ADC
12-Bit
AV+
SAR
ADC0CN
ADC0LTL
12
24
12
COMB
LOGIC
ADWINT