C8051F006-GQR Silicon Laboratories Inc, C8051F006-GQR Datasheet - Page 94
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F006-GQR
Manufacturer Part Number
C8051F006-GQR
Description
IC 8051 MCU 32K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F00xr
Specifications of C8051F006-GQR
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
2.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x12b, D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP, 48-VQFP
For Use With
336-1188 - DEV KIT FOR F005/006/007
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F006-GQR
Manufacturer:
SILICON
Quantity:
1 200
Company:
Part Number:
C8051F006-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
13.1.
The C8051F000 family incorporates a power supply monitor that holds the MCU in the reset state until VDD rises
above the V
Electrical Characteristics of the power supply monitor circuit.) The /RST pin is asserted (low) until the end of the
100ms VDD Monitor timeout in order to allow the VDD supply to become stable.
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. All of the other reset
flags in the RSTSRC Register are indeterminate. PORSF is cleared by a reset from any other source. Since all
resets cause program execution to begin at the same location (0x0000), software can read the PORSF flag to
determine if a power-up was the cause of reset. The content of internal data memory should be assumed to be
undefined after a power-on reset.
13.2.
Writing a 1 to the PORSF bit forces a Power-On Reset as described in Section 13.1.
13.3.
When a power-down transition or power irregularity causes VDD to drop below V
will drive the /RST pin low and return the CIP-51 to the reset state (see Figure 13.2). When VDD returns to a level
above V
though internal data memory contents are not altered by the power-fail reset, it is impossible to determine if VDD
dropped below the level required for data retention. If the PORSF flag is set, the data may no longer be valid.
Logic HIGH
Logic LOW
RST
Power-on Reset
Software Forced Reset
Power-fail Reset
, the CIP-51 will leave the reset state in the same manner as that for the power-on reset. Note that even
2.70
2.40
RST
2.0
1.0
level during power-up. (See Figure 13.2 for timing diagram, and refer to Table 13.1 for the
/RST
Figure 13.2. VDD Monitor Timing Diagram
V
RST
100ms
Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
RST
, the power supply monitor
100ms
t
94