M30281F6HP#U5B Renesas Electronics America, M30281F6HP#U5B Datasheet - Page 85

• Manufacturer Part Number: M30281F6HP#U5B
• Description: IC M16C/28 MCU FLASH 48K 64LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30281F6HP#U5B

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 55
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M
R
R
7.7 System Clock Protective Function
7.8 Oscillation Stop and Re-oscillation Detect Function
e
E
1
. v
Table 7.6 Specification Overview of Oscillation Stop and Re-oscillation Detect Function
J
6
0
When the main clock is selected for the CPU clock source, this function protects the clock from modifica-
tions in order to prevent the CPU clock from becoming halted by run-away.
If the PM21 bit in the PM2 register is set to “1” (clock modification disabled), the following bits are protected
against writes:
Before the system clock protective function can be used, the following register settings must be made while
the CM05 bit in the CM0 register is “0” (main clock oscillating) and CM07 bit is “0” (main clock selected for
the CPU clock source):
(1) Set the PRC1 bit in the PRCR register to “1” (enable writes to PM2 register).
(2) Set the PM21 bit in the PM2 register to “1” (disable clock modification).
(3) Set the PRC1 bit in the PRCR register to “0” (disable writes to PM2 register).
Do not execute the WAIT instruction when the PM21 bit is “1”.
The oscillation stop and re-oscillation detect function detects the re-oscillation after stop of main clock
oscillation circuit. When the oscillation stop and re-oscillation detection occurs, the oscillation stop detect
function is reset or oscillation stop and re-oscillation detection interrupt is generated, depending on the
CM27 bit set in the CM2 register. The oscillation stop detect function is enabled or disabled by the CM20 bit
in the CM2 register. Table 7.6 lists a specification overview of the oscillation stop and re-oscillation detect
function.
Oscillation stop detectable clock and
frequency bandwidth
Enabling condition for oscillation stop,
re-oscillation detection function
Operation at oscillation stop,
re-oscillation detection
C
2
9
• CM02, CM05, and CM07 bits in CM0 register
• CM10, CM11 bits in CM1 register
• CM20 bit in CM2 register
• All bits in PLC0 register
0 .
2 /
B
0
0
8
0
4
G
J
7
a
o r
0 -
. n
u
2
3
p
0
, 1
0
(
Item
M
2
0
1
0
6
7
C
2 /
, 8
page 63
M
1
6
C
f o
2 /
8
3
) B
8
5
f(X
Set CM20 bit to “1”(enable)
•Reset occurs (when CM27 bit is set to "0")
•Oscillation stop, re-oscillation detection interrupt occurs(when
CM27 bit is set to "1")
IN
)
2 MHz
Specification
7. Clock Generation Circuit