DF2378RVFQ34V Renesas Electronics America, DF2378RVFQ34V Datasheet - Page 914

• Manufacturer Part Number: DF2378RVFQ34V
• Description: IC H8S MCU FLASH 512K 144LQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2378RVFQ34V

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 34MHz
• Connectivity: I²C, IrDA, SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 97
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 6x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-LQFP
• For Use With: YLCDRSK2378 - KIT DEV EVAL H8S/2378 LCDYR0K42378FC000BA - KIT EVAL FOR H8S/2378HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)EDK2378 - DEV EVAL KIT FOR H8S/2378
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Section 20 Flash Memory (0.35-μm F-ZTAT Version)
20.6
In an on-board programming mode, programming, erasing, and verification for the on-chip flash
memory can be performed. There are two on-board programming modes: boot mode and user
program mode. Table 20.4 shows how to select boot mode. User program mode can be selected by
setting the control bits by software. For a diagram that shows mode transitions of flash memory,
see figure 20.2.
Table 20.4 Setting On-Board Programming Mode
Boot mode
20.6.1
When this LSI enters boot mode, the embedded boot program is started. The boot program
transfers the programming control program from the externally connected host to the on-chip
RAM via the SCI_1. When the flash memory is all erased, the programming control program is
executed.
Table 20.5 shows the boot mode operations between reset end and branching to the programming
control program.
1. When the boot program is initiated, the SCI_1 should be set to asynchronous mode, the chip
2. After matching the bit rates, the chip transmits one H'00 byte to the host to indicate the end of
Rev.7.00 Mar. 18, 2009 page 846 of 1136
REJ09B0109-0700
measures the low-level period of asynchronous SCI communication data (H'00) transmitted
continuously from the host. The chip then calculates the bit rate of transmission from the host,
and adjusts the SCI_1 bit rate to match that of the host. The transfer format is 8-bit data, 1 stop
bit, and no parity. The reset should end with the RxD pin high. The RxD and TxD pins should
be pulled up on the board if necessary. After the reset ends, it takes approximately 100 states
before the chip is ready to measure the low-level period.
bit rate adjustment. The host should confirm that this adjustment end indication (H'00) has
been received normally, and transmit one H'55 byte to the chip. If reception could not be
performed normally, initiate boot mode again by a reset. Depending on the host’s transfer bit
rate and system clock frequency of this LSI, there will be a discrepancy between the bit rates
of the host and the chip. To operate the SCI properly, set the host’s transfer bit rate and system
clock frequency of this LSI within the ranges listed in table 20.6.
On-Board Programming Modes
Boot Mode
Mode Setting
Single-chip activation expanded
mode with on-chip ROM enabled
MD2
0
MD1
1
MD0
1