ATMEGA3290-16AI Atmel, ATMEGA3290-16AI Datasheet - Page 52

• Manufacturer Part Number: ATMEGA3290-16AI
• Description: IC AVR MCU 32K 16MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA3290-16AI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFPATSTK504 - STARTER KIT AVR EXP MOD 100P LCD
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

11.1.1
11.2
11.2.1
52
Register Description
ATmega329/3290/649/6490
Moving Interrupts Between Application and Boot Space
MCUCR – MCU Control Register
When the BOOTRST Fuse is programmed, the Boot section size set to 4K bytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses is:
The MCU Control Register controls the placement of the Interrupt Vector table.
• Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash
memory. When this bit is set (one), the Interrupt Vectors are moved to the beginning of the Boot
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to the section
Bit
0x35 (0x55)
Read/Write
Initial Value
0x0004
...
0x002C
;
.org 0x3800/0x7800
0x3800/0x7801RESET:ldir16,high(RAMEND); Main program start
0x3801/0x7801
0x3802/0x7802
0x3803/0x7803
0x3804/0x7804
0x3805/0x7805
Address Labels Code
;
.org 0x3800/0x7800
0x3800/0x7800
0x3802/0x7802
0x3804/0x7804
...
0x382C/0x782C
;
0x382E/0x782ERESET:ldir16,high(RAMEND); Main program start
0x382F/0x782F
0x3830/0x7830
0x3831/0x7831
0x3832/0x7832
0x3833/0x7833
JTD
R/W
7
0
jmp
...
jmp
out
ldi
out
sei
<instr>
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
R
6
–
0
PCINT0
...
SPM_RDY
SPH,r16
r16,low(RAMEND)
SPL,r16
RESET
EXT_INT0
PCINT0
...
SPM_RDY
SPH,r16
r16,low(RAMEND)
SPL,r16
R
5
–
0
xxx
xxx
PUD
R/W
4
0
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Set Stack Pointer to top of RAM
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; Enable interrupts
Comments
; Reset handler
; IRQ0 Handler
; PCINT0 Handler
;
; Enable interrupts
R
3
–
0
“Boot Loader Support – Read-While-Write
R
2
–
0
IVSEL
R/W
1
0
IVCE
R/W
0
0
MCUCR
2552K–AVR–04/11