AT91FR40162SB-CU-999 Atmel, AT91FR40162SB-CU-999 Datasheet - Page 53

• Manufacturer Part Number: AT91FR40162SB-CU-999
• Description: IC MCU 32BIT RISC 121BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91FR40162SB-CU-999

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 75MHz
• Connectivity: EBI/EMI, UART/USART
• Peripherals: WDT
• Number Of I /o: 32
• Program Memory Size: 2MB (1M x 16)
• Program Memory Type: FLASH
• Ram Size: 256K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 121-BGA
• Data Bus Width: 32 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

12.2.3
12.2.4
12.2.4.1
12.2.4.2
12.2.5
12.2.6
6410B–ATARM–12-Jan-10
Reset
Erasure
Byte/Word Programming
Program/Erase Status
Chip Erase
Sector Erase
A RESET input pin is provided to ease some system applications. When RESET is at a logic
high level, the device is in its standard operating mode. A low level on the RESET input halts the
present device operation and puts the outputs of the device in a high impedance state. When a
high level is reasserted on the RESET pin, the device returns to the read or standby mode,
depending upon the state of the control inputs.
Before a byte/word can be reprogrammed, it must be erased. The erased state of memory bits is
a logical “1”. The entire device can be erased by using the Chip Erase command or individual
sectors can be erased by using the Sector Erase command.
The entire device can be erased at one time by using the six-byte chip erase software code.
After the chip erase has been initiated, the device will internally time the erase operation so that
no external clocks are required. The maximum time to erase the chip is t
If the sector lockdown has been enabled, the chip erase will not erase the data in the sector that
has been locked out; it will erase only the unprotected sectors. After the chip erase, the device
will return to the read or standby mode.
As an alternative to a full chip erase, the device is organized into 39 sectors (SA0 - SA38) that
can be individually erased. The Sector Erase command is a six-bus cycle operation. The sector
address is latched on the falling WE edge of the sixth cycle while the 30H data input command is
latched on the rising edge of WE. The sector erase starts after the rising edge of WE of the sixth
cycle. The erase operation is internally controlled; it will automatically time to completion. The
maximum time to erase a sector is t
enabled, the sector will erase (from the same Sector Erase command). An attempt to erase a
sector that has been protected will result in the operation terminating immediately.
Once a memory block is erased, it is programmed (to a logical “0”) on a byte-by-byte or on a
word-by-word basis. Programming is accomplished via the internal device command register
and is a four-bus cycle operation. The device will automatically generate the required internal
program pulses.
Any commands written to the chip during the embedded programming cycle will be ignored. If a
hardware reset happens during programming, the data at the location being programmed will be
corrupted. Please note that a data “0” cannot be programmed back to a “1”; only erase opera-
tions can convert “0”s to “1”s. Programming is completed after the specified t
Data Polling feature or the Toggle Bit feature may be used to indicate the end of a program
cycle. If the erase/program status bit is a “1”, the device was not able to verify that the erase or
program operation was performed successfully.
The device provides several bits to determine the status of a program or erase operation: I/O2,
I/O5, I/O6 and I/O7. The
the function of these bits. To provide greater flexibility for system designers, the Flash Memory
contains a programmable configuration register. The configuration register allows the user to
specify the status bit operation. The configuration register can be set to one of two different val-
“Status Bit Table” on page 62
SEC
. When the sector programming lockdown feature is not
and the following four sections describe
AT91FR40162SB
EC
.
BP
cycle time. The
53