LH7A404N0F000B3,55 NXP Semiconductors, LH7A404N0F000B3,55 Datasheet - Page 67

• Manufacturer Part Number: LH7A404N0F000B3,55
• Description: IC ARM9 BLUESTREAK MCU 324LFBGA
• Manufacturer: NXP Semiconductors
• Series: BlueStreak ; LH7Ar

Specifications of LH7A404N0F000B3,55

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, IrDA, Microwire, MMC, PS2, SmartCard, SPI, SSI, SSP, UART/USART, USB
• Peripherals: AC'97, DMA, LCD, POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 80K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-LFBGA
• For Use With: 568-4304 - BOARD EVAL FOR LH7A404
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Other names: 568-4277; 935285069551; LH7A404N0F000B3-S

32-Bit System-on-Chip
Reference Oscillator Circuit Design
design for both the 32.768 kHz and 14.7456 MHz clocks.
Low Operating Temperatures and
Noise Immunity
perature of the transistors in the integrated circuit. The
switching speed of the CMOS circuitry within the SoC
depends partly on Tj, and the lower the operating tem-
perature, the faster the CMOS circuits will switch.
Preliminary data sheet
Figure 52 and Figure 53 show a reference oscillator
The junction temperature, Tj, is the operating tem-
NOTES:
1. Y1 is a parallel-resonant type crystal. (See table)
2. The nominal values for C1 and C2 shown are for
3. The values for C1 and C2 are dependent upon
4. R1 must be in the circuit.
5. Ground connections should be short and return
6. Tolerance for R1, C1, C2 is ≤ 5%.
a crystal specified at 12.5 pF load capacitance (CL).
the cystal's specified load capacitance and PCB
stray capacitance.
to the ground plane which is connected to the
processor's core ground pins.
Figure 52. 32.768 kHz External Oscillator Components and Schematic
INTERNAL TO
THE LH7A404
EXTERNAL TO
THE LH7A404
NXP Semiconductors
ENABLE
XTALIN
REFERENCE CRYSTAL SPECIFICATIONS
PARAMETER
32.768 kHz Crystal
Tolerance
Aging
Load Capacitance
ESR (MAX.)
Drive Level
Reference crystal
Increased switching noise generated by faster switch-
ing circuits could affect the overall system stability. The
amount of switching noise is directly affected by the
application executed on the SoC.
meet the full
nal oscillator rather than a crystal to drive the system
clock input of the System-on-Chip. This change from
crystal to oscillator will increase the robustness (ie,
noise immunity of the clock input to the SoC).
C1
15 pF
NXP suggests that users implementing a system to
GND
32.768 kHz
18 MΩ
Y1
R1
−40
°C to +85°C specification use an exter-
XTALOUT
C2
18 pF
DESCRIPTION
Parallel Mode
±30 ppm
±3 ppm
12.5 pF
50 kΩ
1.0 µW (MAX.)
MTRON SX1555 or equivalent
GND
LH7A404-168
LH7A404
67