Z8F0812SJ020EC Zilog, Z8F0812SJ020EC Datasheet - Page 170
Z8F0812SJ020EC
Manufacturer Part Number
Z8F0812SJ020EC
Description
IC ENCORE MCU FLASH 8K 28SOIC
Manufacturer
Zilog
Series
Encore!® XP®r
Datasheet
1.Z8F08200100KIT.pdf
(264 pages)
Specifications of Z8F0812SJ020EC
Core Processor
Z8
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, IrDA, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
19
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
Other names
269-3228
- Current page: 170 of 264
- Download datasheet (6Mb)
PS022517-0508
Byte Programming
Caution:
Follow the steps below to setup the Flash Sector Protect Register from user code:
1. Write
2. Write
3. Read and/or write the Flash Sector Protect Register which is now at Register File
4. Write
Flash Write Protection Option Bit
The Flash Write Protect option bit can block all program and erase operations from user
code. For more information, see
When the Flash Controller is unlocked, writes to Flash Memory from user code programs
a byte into the Flash if the address is located in the unlocked page. An erased Flash byte
contains all 1s (
change a Flash bit (or multiple bits) from zero to one requires a Page Erase or Mass Erase
operation.
Byte Programming is accomplished using the eZ8 CPU’s LDC or LDCI instructions.
Refer to eZ8 CPU Core User Manual (UM0128) for a description of the LDC and LDCI
instructions.
While the Flash Controller programs the Flash memory, the eZ8 CPU idles but the system
clock and on-chip peripherals continue to operate. Interrupts that occur when a Program-
ming operation is in progress are serviced once the Programming operation is complete.
To exit Programming mode and lock the Flash Controller, write
Register.
User code cannot program Flash Memory on a page that is located in a protected sector.
When user code writes memory locations, only addresses located in the unlocked page are
programmed. Memory writes outside of the unlocked page are ignored.
Follow the steps below to program the Flash from user code:
1. Write
2. Write the page of memory to be programmed to the Page Select Register.
3. Write the first unlock command
4. Write the second unlock command
address
Each memory location must not be programmed more than twice before an
erase occurs.
00H
5EH
00H
00H
FF9H
to the Flash Control Register to reset the Flash Controller.
to the Flash Control Register to select the Flash Sector Protect Register.
to the Flash Control Register to return the Flash Controller to its reset state.
to the Flash Control Register to reset the Flash Controller.
FFH
.
). The programming operation is used to change bits from 1 to 0. To
Option Bits
73H
8CH
to the Flash Control Register.
to the Flash Control Register.
on page 163.
Z8 Encore! XP
00H
Product Specification
to the Flash Control
®
F0822 Series
Flash Memory
157
Related parts for Z8F0812SJ020EC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: