AK5358BETP AKM Semiconductor Inc, AK5358BETP Datasheet
AK5358BETP
Specifications of AK5358BETP
AK5358BETP
Available stocks
Related parts for AK5358BETP
AK5358BETP Summary of contents
Page 1
The AK5358B is a stereo A/D Converter with a wide sampling rate range of 8kHz ∼ 96kHz and it is suitable for consumer to professional audio system. The AK5358B achieves high accuracy and low cost by using Enhanced dual bit ...
Page 2
Ordering Guide AK5358BET AKD5358B ■ Pin Layout AINR AINL CKS1 VCOM VSS1 VA VD VSS2 ■ Compatibility with AK5357, AK5359 and AK5381 AK5357 fs 4kHz to 96kHz S/(N+D) 88dB DR 102dB VIH@TTL Level 2.2V Mode VA (Analog 2.7 to ...
Page 3
No. Pin Name I/O 1 AINR I 2 AINL I 3 CKS1 I 4 VCOM O 5 VSS1 - VSS2 - 9 SDTO O 10 LRCK I/O 11 MCLK I 12 SCLK I/O ...
Page 4
Note 1) Parameter Power Supplies: Analog Digital| Input Current, Any Pin Except Supplies Analog Input Voltage (AINL, AINR, CKS1 pins) Digital Input Voltage Ambient Temperature (powered applied) Storage Temperature Note 1. All voltages with respect to ground. Note 2. ...
Page 5
VA=5.0, VD=5.0V; VSS1=VSS2=0V; fs=48kHz, 96kHz; SCLK=64fs; Signal Frequency=1kHz; 24bit Data; Measurement frequency=20Hz ∼ 20kHz at fs=48kHz, 40Hz ∼ 40kHz at fs=96kHz; unless otherwise specified) Parameter ADC Analog Input Characteristics: Resolution Input Voltage S/(N+D) fs=48kHz BW=20kHz fs=96kHz BW=40kHz DR (−60dBFS, ...
Page 6
VA=4.5 ∼ 5.5V; VD=2.7 ∼ 5.5V) Parameter ADC Digital Filter (Decimation LPF): ±0.1dB Passband (Note 9) −0.2dB −3.0dB Stopband Passband Ripple Stopband Attenuation Group Delay Distortion Group Delay (Note ADC Digital Filter (HPF): −3dB Frequency Response (Note ...
Page 7
DC CHARACTERISTICS (CMOS Level Mode) (Ta=-20°C ∼ 85°C; VA=4.5 ∼ 5.5V; VD=2.7 ∼ 5.5V; CKS2/1/0 = “LLL”, “LHL”, “LHH”, “HHL”, “HHH”) Parameter High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage Input Leakage Current DC CHARACTERISTICS (TTL ...
Page 8
VA=4.5 ∼ 5.5V; VD=2.7 ∼ 5.5V; C Parameter Master Clock Timing 512fs, 256fs Frequency Duty cycle 768fs, 384fs Frequency Duty cycle LRCK Frequency Duty Cycle Slave mode Master mode Audio Interface Timing Slave mode SCLK Period SCLK ...
Page 9
Timing Diagram MCLK LRCK SCLK LRCK tSHLR SCLK tLRS SDTO MS1155-E-00 1/fCLK tCLKH tCLKL dCLK=tCLKH x fCLK, tCLKL x fCLK 1/fs tSCK tSCKH tSCKL Clock Timing tLRSH tSSD Audio Interface Timing (Slave mode [AK5358B] VIH VIL ...
Page 10
LRCK tMSLR SCLK SDTO PDN SDTO PDN MS1155-E-00 tSSD Audio Interface Timing (Master mode) tPDV tPD Power Down & Reset Timing - 10 - [AK5358B] 50%VD dSCK 50%VD 50%VD VIH VIL 50%VD VIL 2010/02 ...
Page 11
System Clock MCLK, SCLK and LRCK (fs) clocks are required in slave mode. The LRCK clock input must be synchronized with MCLK, however the phase is not critical. clock frequency. MCLK frequency, SCLK frequency and master/slave modes are selected ...
Page 12
Audio Interface Format Two kinds of data formats can be selected by the DIF pin compliment format. The SDTO is clocked out on the falling edge of SCLK. The audio interface supports both master and slave modes. In master ...
Page 13
Power Down The AK5358B is placed in power-down mode by bringing the PDN pin “L” or MCLK stop more than 13us, and the digital filter is also reset at the same time. This reset should always be made after ...
Page 14
System Reset The AK5358B must be reset once by bringing the PDN pin “L” or inputting MCLK 13us (min) after the AK5358B is powered-up. In slave mode, the internal timing starts clocking by the rising edge (falling edge at ...
Page 15
Figure 5 shows the system connection diagram. An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. 10u + Rch In + Lch In 10u 2.2u + Analog 5V 10u 0.1u Digital ...
Page 16
Grounding and Power Supply Decoupling The AK5358B requires careful attention to power supply and grounding arrangements. Alternatively if VA and VD are supplied separately, the power up sequence is not critical. VSS1 and VSS2 of the AK5358B must be ...
Page 17
TSSOP (Unit: mm) *5.0±0 0.22±0.1 M 0.13 Seating Plane NOTE: Dimension "*" does not include mold flash. ■ Material & Lead finish Package molding compound: Lead frame material: Lead frame surface treatment: MS1155-E-00 PACKAGE 9 8 0.65 ...
Page 18
Date (YY/MM/DD) Revision 10/02/09 00 MS1155-E-00 MARKING AKM 5358BET XXYYY Pin #1 indication 1) Date Code: XXYYY (5 digits) 2) XX: Lot# YYY: Date Code Marketing Code: 5358BET 3) REVISION HISTORY Reason Page Contents First Edition - 18 - [AK5358B] ...
Page 19
These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status ...