MC9S08AC32CPUE Freescale Semiconductor, MC9S08AC32CPUE Datasheet - Page 59

• Manufacturer Part Number: MC9S08AC32CPUE
• Description: IC MCU 8BIT 32K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08AC32CPUE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08AC
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08AC60E, DEMOACEX, DEMOACKIT, DCF51AC256, DC9S08AC128, DC9S08AC16, DC9S08AC60, DEMO51AC256KIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.6.2
During reset, the contents of the nonvolatile location NVOPT are copied from FLASH into FOPT. Bits 5
through 2 are not used and always read 0. This register may be read at any time, but writes have no meaning
or effect. To change the value in this register, erase and reprogram the NVOPT location in FLASH memory
as usual and then issue a new MCU reset.
4.6.3
Bits 7 through 5 may be read or written at any time. Bits 4 through 0 always read 0 and cannot be written.
Freescale Semiconductor
SEC0[1:0]
FNORED
Reset
KEYEN
Field
1:0
7
6
W
R
KEYEN
FLASH Options Register (FOPT and NVOPT)
FLASH Configuration Register (FCNFG)
Backdoor Key Mechanism Enable — When this bit is 0, the backdoor key mechanism cannot be used to
disengage security. The backdoor key mechanism is accessible only from user (secured) firmware. BDM
commands cannot be used to write key comparison values that would unlock the backdoor key. For more detailed
information about the backdoor key mechanism, refer to
0 No backdoor key access allowed.
1 If user firmware writes an 8-byte value that matches the nonvolatile backdoor key (NVBACKKEY through
Vector Redirection Disable — When this bit is 1, vector redirection is disabled.
0 Vector redirection enabled.
1 Vector redirection disabled.
Security State Code — This 2-bit field determines the security state of the MCU as shown below. When the
MCU is secure, the contents of RAM and FLASH memory cannot be accessed by instructions from any
unsecured source including the background debug interface. For more detailed information about security, refer
to
00 Secure
01 Secure
10 Unsecured
11 Secure
SEC0[1:0] changes to 10 after successful backdoor key entry or a successful blank check of FLASH.
7
Section 4.5,
NVBACKKEY+7, in that order), security is temporarily disengaged until the next MCU reset.
= Unimplemented or Reserved
FNORED
“Security.”
6
This register is loaded from nonvolatile location NVOPT during reset.
Figure 4-5. FLASH Options Register (FOPT)
MC9S08AC60 Series Data Sheet, Rev. 2
Table 4-8. FOPT Field Descriptions
0
5
0
4
Description
Section 4.5,
0
3
“Security.”
0
2
SEC01
1
Chapter 4 Memory
SEC00
0
59