MCF5280CVM66 Freescale Semiconductor, MCF5280CVM66 Datasheet - Page 117

• Manufacturer Part Number: MCF5280CVM66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5280CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• No. Of I/o's: 150
• Program Memory Size: 2KB
• Ram Memory Size: 64KB
• Cpu Speed: 66.67MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

6.3.1
The CFM configuration field comprises 24 bytes of reserved array memory space that determines the
module protection and access restrictions out of reset. Data to secure the Flash from unauthorized access
is also stored in the CFM configuration field.
6.3.2
The configuration information in the Flash base address register (FLASHBAR) controls the operation of
the Flash module.
The FLASHBAR register contains several control fields. These fields are shown in
Freescale Semiconductor
•
•
•
•
•
0x0000_040C–0x0000_040F
0x0000_0408–0x0000_040B
Address Offset (from array
0x0000_0400–0x0000_0407
0x0000_0410–0x0000_0413
0x0000_0414–0x0000_0417
The FLASHBAR holds the base address of the Flash. The MOVEC instruction provides write-only
access to this register.
The FLASHBAR can be read or written from the debug module in a similar manner.
All undefined bits in the register are reserved. These bits are ignored during writes to the
FLASHBAR, and return zeroes when read from the debug module.
The back door enable bit, FLASHBAR[BDE], is cleared at reset, disabling back door access to the
Flash.
The FLASHBAR valid bit is programmed according to the chip mode selected at reset (see
Chapter 27, “Chip Configuration Module
base address)
CFM Configuration Field
Flash Base Address Register (FLASHBAR)
The default value of the FLASHBAR is determined by the chip
configuration selected at reset (see
Module
the FLASHBAR located in the processor’s CPU space will be invalid and it
must be initialized with the valid bit set before the CPU (or modules) can
access the on-chip Flash.
(CCM)” for more information). If external boot mode is used, then
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
in Bytes
Size
Table 6-1. CFM Configuration Field
8
4
4
4
4
Back door comparison key
Flash program/erase sector protection
Blocks 0H/0L (see
(CFMPROT)”)
Flash supervisor/user space restrictions
Blocks 0H/0L (see
(CFMSACC)”)
Flash program/data space restrictions
Blocks 0H/0L (see
(CFMDACC)”)
Flash security longword (see
(CFMSEC)”)
Table 6-1
NOTE
(CCM)” for more details). All other bits are unaffected.
Chapter 27, “Chip Configuration
describes each byte used in this field.
Section 6.3.4.4, “CFM Protection Register
Section 6.3.4.5, “CFM Supervisor Access Register
Section 6.3.4.6, “CFM Data Access Register
Description
Section 6.3.4.3, “CFM Security Register
ColdFire Flash Module (CFM)
Figure 6-3
6-5