MCF5280CVM66 Freescale Semiconductor, MCF5280CVM66 Datasheet - Page 411

• Manufacturer Part Number: MCF5280CVM66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5280CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• No. Of I/o's: 150
• Program Memory Size: 2KB
• Ram Memory Size: 64KB
• Cpu Speed: 66.67MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

22.3.5
The QAR is used to specify the location in the QSPI RAM that read and write operations affect. As shown
in
is located at 0x10 to 0x1F, and the command RAM is located at 0x20 to 0x2F. (These addresses refer to
the QSPI RAM space, not the device memory map.)
Freescale Semiconductor
WCEFB
WCEFE
ABRTB
ABRTE
ABRTL
SPIFE
WCEF
ABRT
Field
SPIF
Section 22.4.1, “QSPI
7–4
15
14
13
12
11
10
9
8
3
2
1
0
Write collision access error enable. A write collision occurs during a data transfer when the RAM entry containing
the current command is written to by the CPU with the QDR. When this bit is asserted, the write access to QDR
results in an access error.
Abort access error enable. An abort occurs when QDLYR[SPE] is cleared during a transfer. When set, an attempt to
clear QDLYR[SPE] during a transfer results in an access error.
Reserved, must be cleared.
Abort lock-out. When set, QDLYR[SPE] cannot be cleared by writing to the QDLYR. QDLYR[SPE] is only cleared by
the QSPI when a transfer completes.
Write collision (WCEF) interrupt enable.
0 Write collision interrupt disabled
1 Write collision interrupt enabled
Abort (ABRT) interrupt enable.
0 Abort interrupt disabled
1 Abort interrupt enabled
Reserved, must be cleared.
QSPI finished (SPIF) interrupt enable.
0 SPIF interrupt disabled
1 SPIF interrupt enabled
Reserved, must be cleared.
Write collision error flag. Indicates that an attempt has been made to write to the RAM entry that is currently being
executed. Writing a 1 to this bit (w1c) clears it and writing 0 has no effect.
Abort flag. Indicates that QDLYR[SPE] has been cleared by the user writing to the QDLYR rather than by completion
of the command queue by the QSPI. Writing a 1 to this bit (w1c) clears it and writing 0 has no effect.
Reserved, must be cleared.
QSPI finished flag. Asserted when the QSPI has completed all the commands in the queue. Set on completion of
the command pointed to by QWR[ENDQP], and on completion of the current command after assertion of
QWR[HALT]. In wraparound mode, this bit is set every time the command pointed to by QWR[ENDQP] is completed.
Writing a 1 to this bit (w1c) clears it and writing 0 has no effect.
QSPI Address Register (QAR)
A read or write to the QSPI RAM causes QAR to increment. However, the
QAR does not wrap after the last queue entry within each section of the
RAM. The application software must manage address range errors.
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
RAM”, the transmit RAM is located at addresses 0x0 to 0xF, the receive RAM
Table 22-6. QIR Field Descriptions
NOTE
Description
Queued Serial Peripheral Interface (QSPI)
22-7