XR16L2750IM-F Exar Corporation, XR16L2750IM-F Datasheet - Page 4
![IC UART FIFO 64B DUAL 48TQFP](/photos/16/10/161019/tqfp-48_sml.jpg)
XR16L2750IM-F
Manufacturer Part Number
XR16L2750IM-F
Description
IC UART FIFO 64B DUAL 48TQFP
Manufacturer
Exar Corporation
Type
IrDA or RS- 485r
Datasheet
1.XR16L2750CM-F.pdf
(48 pages)
Specifications of XR16L2750IM-F
Number Of Channels
2, DUART
Package / Case
48-TQFP
Features
*
Fifo's
64 Byte
Protocol
RS232, RS485
Voltage - Supply
2.25 V ~ 5.5 V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Data Rate
6.25 Mbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.25 V
Supply Current
5 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
2.5 V or 3.3 V or 5 V
No. Of Channels
2
Uart Features
Tx/Rx FIFO Counters
Supply Voltage Range
2.25V To 5.5V
Operating Temperature Range
-40°C To +85°C
Digital Ic Case Style
TQFP
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
1016-1280
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XR16L2750IM-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
XR16L2750IM-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
XR16L2750
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
Pin Description
RXRDYB#
DSRA#
RTSA#
CTSA#
DTRA#
OP2A#
CDA#
N
RIA#
RXA
TXA
TXB
AME
44-PLCC
P
23
13
36
40
37
41
42
43
35
14
IN
11
#
48-TQFP
P
18
33
38
34
39
40
41
32
IN
7
5
8
#
MODEM OR SERIAL I/O INTERFACE
T
YPE
O
O
O
O
O
O
I
I
I
I
I
UART channel B Receiver Ready (active low). This output provides the
RX FIFO/RHR status for receive channel B. See
used, leave it unconnected.
UART channel A Transmit Data or infrared encoder data. Standard
transmit and receive interface is enabled when MCR[6] = 0. In this
mode, the TX signal will be HIGH during reset or idle (no data). Infrared
IrDA transmit and receive interface is enabled when MCR[6] = 1. In the
Infrared mode, the inactive state (no data) for the Infrared encoder/
decoder interface is LOW. If it is not used, leave it unconnected.
UART channel A Receive Data or infrared receive data. Normal receive
data input must idle HIGH. The infrared receiver pulses typically idles at
LOW but can be inverted by software control prior going in to the
decoder, see MCR[6] and FCTR[2]. If this pin is not used, tie it to VCC
or pull it high via a 100k ohm resistor.
UART channel A Request-to-Send (active low) or general purpose out-
put. This output must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1], FCTR[1:0], EMSR[5:4] and IER[6]. For auto
RS485 half-duplex direction control, see FCTR[3] and EMSR[3].
UART channel A Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
UART channel A Data-Terminal-Ready (active low) or general purpose
output. If it is not used, leave it unconnected.
UART channel A Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
UART channel A Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
UART channel A Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
Output Port 2 Channel A - The output state is defined by the user and
through the software setting of MCR[3]. INTA is set to the active mode
and OP2A# output LOW when MCR[3] is set to a logic 1. INTA is set to
the three state mode and OP2A# output HIGH when MCR[3] is set to a
logic 0. See MCR[3]. This output should not be used as a general out-
put else it will disturb the INTA output functionality.
UART channel B Transmit Data or infrared encoder data. Standard
transmit and receive interface is enabled when MCR[6] = 0. In this
mode, the TX signal will be HIGH during reset or idle (no data). Infrared
IrDA transmit and receive interface is enabled when MCR[6] = 1. In the
Infrared mode, the inactive state (no data) for the Infrared encoder/
decoder interface is LOW. If it is not used, leave it unconnected.
4
D
ESCRIPTION
Table 2
xr
. If it is not
REV. 1.2.1