X09-009PKC-RA Digi International/Maxstream, X09-009PKC-RA Datasheet - Page 29

• Manufacturer Part Number: X09-009PKC-RA
• Description: MOD RF 900MHZ 9600BPS RS232/485
• Manufacturer: Digi International/Maxstream
• Series: XStream™r

Specifications of X09-009PKC-RA

• Function: Transceiver, FHSS
• Modulation Or Protocol: FHSS, FSK
• Frequency: 900MHz
• Applications: ISM
• Interface: RS-232, RS-485
• Sensitivity: -110dBm
• Power - Output: 20dBm (100mW)
• Data Rate - Maximum: 10 kbps
• Voltage - Supply: 7 V ~ 18 V
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -

© 2006 MaxStream, Inc. Confidential & Proprietary
XStream‐PKG‐R™ RS‐232/485 RF Modem – Product Manual v5.x00 [2006.02.24]
DR (DI3 Configuration) Command
DT (Destination Address) Command
E0 (Echo Off) Command
E1 (Echo On) Command
ER (Receive Error Count) Command
<Serial Interfacing> The DR Command is used to
configure the DI3 (Data Input 3 / SLEEP) line for
I/O line passing (use with CD = 1 or 2 and CO)
or controlling connection status (use with MD = 1
or 2).
<Networking> DT Command is used to set the
networking address of an XStream Modem.
XStream Modems use three filtration layers –
Vendor Identification Number (ATID), Channels
(ATHP) and Destination Addresses (ATDT). DT
Command assigns an address to a modem that
enables it to communicate only with other
modems having the same addresses. All modems
that share the same Destination Address can
communicate freely with each other. Modems in
the same network with a different Destination Address (than that of the transmitter) will listen to
all transmissions to stay synchronized, but will not send any of the data out their serial ports.
<Command Mode Options> E0 Command turns
off character echo in AT Command Mode. By
default, echo is off.
<Command Mode Options> E1 Command turns
on the echo in AT Command Mode. Each typed
character will be echoed back to the terminal
when ATE1 is active. E0 is the default.
<Diagnostics> Set/Read the receive-error. The
error-count records the number of packets
partially received then aborted on a reception
error. This value returns to 0 after a reset and is
not non-volatile (Value does not persist in the
modem’s memory after a power-up sequence).
Once the “Receive Error Count” reaches its
maximum value (up to 0xFFFF), it remains at its
maximum count value until the maximum count
value is explicitly changed or the modem is reset.
AT Command: ATDR
Binary Command: 0x2D (45 decimal)
Parameter Range: 0 – 4
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: CD (DO3 Configuration),
CO (DO3 Timeout), MD (RF Mode)
Minimum Firmware Version Required: 4.30
AT Command: ATDT
Binary Command: 0x00
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: HP (Hopping Channel), ID
(Modem VID), MK (Address Mask)
AT Command: ATE0
Binary Command: 0x0A (10 decimal)
AT Command: ATE1
Binary Command: 0x0B (11 decimal)
AT Command: ATER
Binary Command: 0x0F (15 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: GD (Receive Good Count)
Parameter
0
1
2
3
4
DI3 I/O passing enabled
Connect and Disconnect
Disconnect on high
Connect on low
Configuration
Disabled
29