SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 197

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

20.2. SmaRTClock Clocking Sources
The SmaRTClock peripheral is clocked from its own timebase, independent of the system clock. The
SmaRTClock timebase is derived from the SmaRTClock oscillator circuit, which has two modes of opera-
tion: Crystal Mode, and Self-Oscillate Mode. The oscillation frequency is 32.768 kHz in Crystal Mode and
can be programmed in the range of 10 kHz to 40 kHz in Self-Oscillate Mode. The frequency of the SmaRT-
Clock oscillator can be measured with respect to another oscillator using an on-chip timer. See Section
“27. Timers” on page 330 for more information on how this can be accomplished.
Note: The SmaRTClock timebase can be selected as the system clock and routed to a port pin. See Section
20.2.1. Using the SmaRTClock Oscillator with a Crystal or External CMOS Clock
When using Crystal Mode, a 32.768 kHz crystal should be connected between XTAL3 and XTAL4. No
other external components are required. The following steps show how to start the SmaRTClock crystal
oscillator in software:
1. Set SmaRTClock to Crystal Mode (XMODE = 1).
2. Disable Automatic Gain Control (AGCEN) and enable Bias Doubling (BIASX2) for fast crystal startup.
3. Set the desired loading capacitance (RTC0XCF).
4. Enable power to the SmaRTClock oscillator circuit (RTC0EN = 1).
5. Wait 20 ms.
6. Poll the SmaRTClock Clock Valid Bit (CLKVLD) until the crystal oscillator stabilizes.
7. Poll the SmaRTClock Load Capacitance Ready Bit (LOADRDY) until the load capacitance reaches its
8. Enable Automatic Gain Control (AGCEN) and disable Bias Doubling (BIASX2) for maximum power
9. Enable the SmaRTClock missing clock detector.
10.Wait 2 ms.
11. Clear the PMU0CF wake-up source flags.
In Crystal Mode, the SmaRTClock oscillator may be driven by an external CMOS clock. The CMOS clock
should be applied to XTAL3. XTAL4 should be left floating. The input low voltage (VIL) and input high volt-
age (VIH) for XTAL3 when used with an external CMOS clock are 0.1 and 0.8 V, respectively. The SmaRT-
Clock oscillator should be configured to its lowest bias setting with AGC disabled. The CLKVLD bit is
indeterminate when using a CMOS clock, however, the OSCFAIL bit may be checked 2 ms after SmaRT-
Clock oscillator is powered on to ensure that there is a valid clock on XTAL3.
20.2.2. Using the SmaRTClock Oscillator in Self-Oscillate Mode
When using Self-Oscillate Mode, the XTAL3 and XTAL4 pins should be shorted together. The RTC0PIN
register can be used to internally short XTAL3 and XTAL4. The following steps show how to configure
SmaRTClock for use in Self-Oscillate Mode:
1. Set SmaRTClock to Self-Oscillate Mode (XMODE = 0).
2. Set the desired oscillation frequency:
3. The oscillator starts oscillating instantaneously.
4. Fine tune the oscillation frequency by adjusting the load capacitance (RTC0XCF).
programmed value.
savings.
For oscillation at about 20 kHz, set BIASX2 = 0.
For oscillation at about 40 kHz, set BIASX2 = 1.
“19. Clocking Sources” on page 182 for information on selecting the system clock source and Section “21. Port
Input/Output” on page 207 for information on how to route the system clock to a port pin.
Rev. 1.0
Si1000/1/2/3/4/5
197