XR18W750IL48-F Exar Corporation, XR18W750IL48-F Datasheet - Page 4

• Manufacturer Part Number: XR18W750IL48-F
• Description: IC WIRELESS UART CTRLR 48QFN
• Manufacturer: Exar Corporation

Specifications of XR18W750IL48-F

• Package / Case: 48-VFQFN Exposed Pad
• Function: Controller
• Rf Type: General Purpose
• Secondary Attributes: I²C Interface
• Processor Series: XR18W750
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 32 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 400 KHz
• Number Of Timers: 1
• Operating Supply Voltage: 2.25 V to 3.63 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: XR18W750/753-0A-EB, XR18W750/753-0B-EB
• Minimum Operating Temperature: - 40 C
• Program Memory Type: EEPROM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Pin Description
XR18W750
WIRELESS UART CONTROLLER
RF TRANSCEIVER INTERFACE SIGNALS
ANCILLARY SIGNALS
MODEM_RESET
(RESET#)
EN_DIDO
RF_IRQ#
RF_DO
RESET
16/68#
RF_DI
RTS#
CTS#
DTR#
DSR#
N
S/P#
CD#
SDA
SCL
RI#
AME
48-QFN
P
41
39
38
42
37
40
11
12
10
36
46
17
45
IN
1
8
9
#
T
I/O
I/O
YPE
O
O
O
O
I
I
I
I
I
I
I
I
I
I
UART Request-to-Send (active low) or general purpose output. This output must
be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6].
UART Clear-to-Send (active low) or general purpose input. It can be used for
auto CTS flow control, see EFR[7], and IER[7]. This input should be connected to
VCC when not used.
UART Data-Terminal-Ready (active low) or general purpose output. If it is not
used, leave it unconnected.
UART Data-Set-Ready (active low) or general purpose input. This input should
be connected to VCC when not used. This input has no effect on the UART.
UART Carrier-Detect (active low) or general purpose input. This input should be
connected to VCC when not used. This input has no effect on the UART.
UART Ring-Indicator (active low) or general purpose input. This input should be
connected to VCC when not used. This input has no effect on the UART.
Reset output to the RF transceiver.
Interrupt input from RF transceiver.
I
I
Data out to RF transceiver.
Data in from RF transceiver.
Enable RF_DI and RF_DO (active high) for sending data to and from RF trans-
ceiver. If I
GND.
Serial or Parallel Mode select. If this pin is HIGH, then the serial interface will be
enabled. If this pin is LOW, then the parallel mode will be enabled.
Intel or Motorola Bus Select.
When 16/68# pin is HIGH, 16 or Intel Mode, the device will operate in the Intel
bus type of interface.
When 16/68# pin is LOW, 68 or Motorola mode, the device will operate in the
Motorola bus type of interface.
When 16/68# pin is HIGH for Intel bus interface, this input becomes RESET
(active high). When 16/68# pin is LOW for Motorola bus interface, this input
becomes RESET# (active low).
A 40 ns minimum active pulse on this pin will reset the internal registers and all
outputs. The UART transmitter output will be held HIGH, the receiver input will be
ignored and outputs are reset during reset period (see
2
2
C Serial Data Line.
C Serial Clock Line. The I
2
C bus is used for this purpose, this input should be connected to
4
2
C clock frequency can be up to 400 KHz.
D
ESCRIPTION
Table 15
).
REV. 1.0.0