PCA9507DP,118 NXP Semiconductors, PCA9507DP,118 Datasheet - Page 8
![I/O Expanders, Repeaters & Hubs LEVEL TRANSL I2C BUS](/photos/16/10/161075/pca-tssop-8_sml.jpg)
PCA9507DP,118
Manufacturer Part Number
PCA9507DP,118
Description
I/O Expanders, Repeaters & Hubs LEVEL TRANSL I2C BUS
Manufacturer
NXP Semiconductors
Series
-r
Datasheet
1.PCA9507DP118.pdf
(20 pages)
Specifications of PCA9507DP,118
Logic Family
SDA, SCL
Propagation Delay Time
218 ns
Operating Supply Voltage
2.7 V to 5.5 V
Power Dissipation
100 mW
Operating Temperature Range
- 40 C to + 85 C
Logic Type
I2C Bus
Mounting Style
SMD/SMT
Output Current
50 mA
Output Voltage
0.52 V
Package / Case
TSSOP-8
Mounting Type
Surface Mount
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Interface
I²C, SMBus
Number Of I /o
24
Frequency - Clock
400kHz
Interrupt Output
No
Includes
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
935285824118 PCA9507DP-T
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PCA9507DP,118
Manufacturer:
MCC
Quantity:
40 000
Part Number:
PCA9507DP,118
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
PCA9507_1
Product data sheet
According to
I
the internal driver on port B to turn on, causing port B to pull down to about 0.5 V. When
port B of the PCA9507 falls, first a CMOS hysteresis type input detects the falling edge
and causes the internal driver on port A to turn on and pull the port A pin down to ground.
In order to illustrate what would be seen in a typical application, refer to
Figure
If the bus master in
shown in
transmission except that the HIGH level may be as low as 2.7 V, and the turn on and turn
off of the acknowledge signals are slightly delayed.
The master drives the B bus to ground or lets it float to V
at the falling edge of the 8
SDAA on the A bus to ground, causing the PCA9507 to pull SDAB on the B bus to 0.5 V.
At the falling edge of the 9
the A bus.
Multiple PCA9507 port A sides can be connected in a star configuration
allowing all nodes to communicate with each other.
Multiple PCA9507s can be connected in series
to port B. I
number of devices that can be connected in series is limited by repeater
delay/time-of-flight considerations on the maximum bus speed requirements.
2
C-bus, a comparator detects the falling edge when it goes below 0.3V
12.
Figure 11
2
C-bus slave devices can be connected to any of the bus segments. The
Figure
would be observed on the A bus. This looks like a normal I
Figure 6
6, when port A of the PCA9507 is pulled LOW by a driver on the
Rev. 01 — 7 February 2008
2-wire serial bus extender for HDMI DDC I
th
th
clock, master releases SDAB on the B bus and slave pulls
clock, the master again drives the B bus and slave releases
were to write to the slave through the PCA9507, waveforms
(Figure
10) as long as port A is connected
CC(B)
as it sends data to the slave
2
PCA9507
C-bus and SMBus
© NXP B.V. 2008. All rights reserved.
CC(A)
Figure 11
(Figure
and causes
2
C-bus
9),
and
8 of 20