142-0403-101 Emerson Network Power, 142-0403-101 Datasheet - Page 12

• Manufacturer Part Number: 142-0403-101
• Description: CONN PLUG RIGHT ANGLE CRIMP GOLD
• Manufacturer: Emerson Network Power
• Series: SMAr
• Type: Cable Plugr

Specifications of 142-0403-101

• Connector Style: SMA
• Connector Type: Plug, Male Pins
• Contact Termination: Crimp and Solder
• Impedance: 50 Ohm
• Mounting Type: Free Hanging (In-Line), Right Angle
• Fastening Type: Threaded
• Cable Group: RG-161, 174, 188, 316, LMR-100
• Frequency - Max: 12.4GHz
• Frequency-max: 12.4GHz
• Body Style: Right Angle
• Cable Type: RG 161/U, 174, 188, 316, LMR100, HPF100, RF100
• Features: Captivated contact
• Frequency Range: 0 GHz to to 12.4 GHz
• Housing Material: Brass
• Mounting Angle: Right
• Operating Temperature Range: - 65 C to + 165 C
• Rf Series: SMA
• Product: Various Connectors
• Contact Plating: Gold
• Shell Plating: Gold
• Termination Style: Crimp
• Maximum Frequency: 12.4 GHz
• Angle: Right-Angle
• Finish, Housing: Gold
• Material, Contact: Brass
• Material, Dielectric: TFE
• Material, Housing: Brass
• Primary Type: SMA
• Special Features: Captivated Contact
• Termination: Crimp
• Voltage, Rating: 250 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 140-0403-101; 1420403101; J510

Assembly
Instructions
SMA CRIMP TYPE STRAIGHT PLUGS,
STRAIGHT JACKS, AND STRAIGHT BULKHEAD
JACKS FOR FLEXIBLE CABLE
12
Johnson Components
®
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: [phone] • www.johnsoncomp.com
1. Identify connector parts. (6 piece parts - except bulkhead)
2. Strip cable to dimensions shown. Do not nick braid or cen-
3. Flare braid and slide cable into crimp stem. Place rear
4. Arrange braid uniformly around crimp stem. Slide crimp
ter conductor. A wire stripper of correct size is recom-
mended for this step. Twist stranded center conductor into
tight bundle and tin (optional). Slide crimp sleeve, nut and
heat shrink tubing (as applicable) onto cable as shown.
insulator and center contact over center conductor and po-
sition as shown for different cable sizes. Solder center
conductor to contact through the solder hole. Solder must
not be allowed to gather and run on outside of contact.
Use a minimum amount of solder for a good joint. .020
(0.51) diameter solder is recommended.
sleeve over braid and crimp securely using recommended
crimp tool. Slide center contact assembly into connector
body. Thread coupling nut onto body and tighten to 10 in.-
lb. torque. Slide heat shrink forward and shrink (as appli-
cable).
CABLE GROUP
RG 316/u, 161,
RG 316/u, 161,
RG 316/u, 161,
RG 55/u, 142,
RG 55/u, 142,
RG 55/u, 142,
RG 316DS,
RG 316DS,
RG 316DS,
RG 178/u,
RG 178/u,
RG 178/u,
174, 188
RG 58/u,
RG 58/u,
141, 303
223, 400
RG 58/u,
141, 303
223, 400
141, 303
223, 400
174, 188
174, 188
188DS
188DS
188DS
196
196
196
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
PART NUMBER CRIMP HEX
142-0302-001
142-0302-006
142-0303-001
142-0303-006
142-0304-001
142-0304-006
142-0307-001
142-0307-006
142-0308-001
142-0308-006
142-0302-401
142-0302-406
142-0303-401
142-0303-406
142-0304-401
142-0304-406
142-0307-401
142-0307-406
142-0308-401
142-0308-406
142-0402-001
142-0402-006
142-0403-001
142-0403-006
142-0404-001
142-0404-006
142-0407-001
142-0407-006
142-0408-001
142-0408-006
INCHES (MILLIMETERS)
.105 (2.67)
.105 (2.67)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.105 (2.67)
.105 (2.67)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.105 (2.67)
.105 (2.67)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)