142-0403-101 Emerson Network Power, 142-0403-101 Datasheet - Page 13

• Manufacturer Part Number: 142-0403-101
• Description: CONN PLUG RIGHT ANGLE CRIMP GOLD
• Manufacturer: Emerson Network Power
• Series: SMAr
• Type: Cable Plugr

Specifications of 142-0403-101

• Connector Style: SMA
• Connector Type: Plug, Male Pins
• Contact Termination: Crimp and Solder
• Impedance: 50 Ohm
• Mounting Type: Free Hanging (In-Line), Right Angle
• Fastening Type: Threaded
• Cable Group: RG-161, 174, 188, 316, LMR-100
• Frequency - Max: 12.4GHz
• Frequency-max: 12.4GHz
• Body Style: Right Angle
• Cable Type: RG 161/U, 174, 188, 316, LMR100, HPF100, RF100
• Features: Captivated contact
• Frequency Range: 0 GHz to to 12.4 GHz
• Housing Material: Brass
• Mounting Angle: Right
• Operating Temperature Range: - 65 C to + 165 C
• Rf Series: SMA
• Product: Various Connectors
• Contact Plating: Gold
• Shell Plating: Gold
• Termination Style: Crimp
• Maximum Frequency: 12.4 GHz
• Angle: Right-Angle
• Finish, Housing: Gold
• Material, Contact: Brass
• Material, Dielectric: TFE
• Material, Housing: Brass
• Primary Type: SMA
• Special Features: Captivated Contact
• Termination: Crimp
• Voltage, Rating: 250 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 140-0403-101; 1420403101; J510

INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
SMA CRIMP TYPE RIGHT ANGLE PLUGS
FOR FLEXIBLE CABLE
Johnson Components
®
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: [phone] • www.johnsoncomp.com
1. Identify connector parts. (3 piece parts)
2. Strip cable to dimensions shown. Do not nick braid or cen-
3. Flare braid and slide cable into body making certain that
4. Arrange braid uniformly around crimp stem. Slide crimp
ter conductor. When stripping LMR-100 low loss cable,
remove foil back to where cable jacket is stripped. A wire
stripper of correct size is recommended for this step. Twist
stranded center conductor into tight bundle and tin (op-
tional). Slide crimp sleeve onto cable as shown.
the cable insulation bottoms on center contact. Solder
center conductor to contact through the rear access port.
Use a minimum amount of solder for a full fillet joint. .020
(0.51) diameter solder is recommended.
sleeve over braid and crimp securely using recommended
crimp tool. Place expansion cap in access port and seat
with .187 (4.75) diameter flat punch. Shrink heat shrink
tubing over crimp sleeve if applicable.
174, 188; LMR-100
174, 188; LMR-100
174, 188; LMR-100
CABLE GROUP
RG 316/u, 161,
RG 316/u, 161,
RG 316/u, 161,
RG 55/u, 142,
RG 55/u, 142,
RG 55/u, 142,
RG 316DS,
RG 316DS,
RG 316DS,
RG 178/u,
RG 179/u,
RG 58/u,
RG 58/u,
141, 303
RG 58/u,
141, 303
223, 400
223, 400
141, 303
223, 400
188DS
188DS
188DS
196
187
Instructions
Assembly
PART NUMBER
142-0402-101
142-0402-106
142-0403-101
142-0403-106
142-0404-101
142-0404-106
142-0407-101
142-0407-106
142-0408-101
142-0408-106
142-0433-101
142-0433-106
142-4403-101
142-4403-106
142-4404-101
142-4404-106
142-4407-101
142-4407-106
142-4408-101
142-4408-106
142-5403-101
142-5403-106
142-5404-101
142-5404-106
142-5407-101
142-5407-106
142-5408-101
142-5408-106
CRIMP HEX
.105 (2.67)
.105 (2.67)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.128 (3.25)
.128 (3.25)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
13