142-0403-101 Emerson Network Power, 142-0403-101 Datasheet - Page 14

• Manufacturer Part Number: 142-0403-101
• Description: CONN PLUG RIGHT ANGLE CRIMP GOLD
• Manufacturer: Emerson Network Power
• Series: SMAr
• Type: Cable Plugr

Specifications of 142-0403-101

• Connector Style: SMA
• Connector Type: Plug, Male Pins
• Contact Termination: Crimp and Solder
• Impedance: 50 Ohm
• Mounting Type: Free Hanging (In-Line), Right Angle
• Fastening Type: Threaded
• Cable Group: RG-161, 174, 188, 316, LMR-100
• Frequency - Max: 12.4GHz
• Frequency-max: 12.4GHz
• Body Style: Right Angle
• Cable Type: RG 161/U, 174, 188, 316, LMR100, HPF100, RF100
• Features: Captivated contact
• Frequency Range: 0 GHz to to 12.4 GHz
• Housing Material: Brass
• Mounting Angle: Right
• Operating Temperature Range: - 65 C to + 165 C
• Rf Series: SMA
• Product: Various Connectors
• Contact Plating: Gold
• Shell Plating: Gold
• Termination Style: Crimp
• Maximum Frequency: 12.4 GHz
• Angle: Right-Angle
• Finish, Housing: Gold
• Material, Contact: Brass
• Material, Dielectric: TFE
• Material, Housing: Brass
• Primary Type: SMA
• Special Features: Captivated Contact
• Termination: Crimp
• Voltage, Rating: 250 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 140-0403-101; 1420403101; J510

Assembly
Instructions
Right Angle SMA Low Loss Diameter .195, .200 and .240
14
Johnson Components
®
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: [phone] • www.johnsoncomp.com
Low Loss Dia.
1. Identify connector parts. (3 piece parts)
2. Strip cable to dimensions shown. Do not nick braid, foil or center con-
3. Flare braid and slide body assembly over foil and dielectric, then un-
4. Arrange braid uniformly around crimp stem. Slide crimp sleeve for-
0.195
0.200
0.240
ductor. Cut foil flush with dielectric, do not remove foil. Make sure that
dielectric is clean and free from all particles. Tin center conductor,
keeping solder amount to a minimum. Slide crimp sleeve onto jacket
of cable.
der braid. Make sure cable center conductor is contained within con-
nector contact, but do not allow foil and dielectric to enter body access
port. Solder center conductor to contact through the rear access port.
Use a minimum amount of solder for a full fillet joint. .020 (0.51) Diam-
eter solder is recommended.
ward and crimp using JCI hand crimp tool 141-0000-913 and recom-
mended crimp die hex. Place expansion cap in access port and seat
with recommended Diameter flat punch.
.110 (2.79)
.110 (2.79)
.135 (3.43)
“A”
CABLE GROUP
LMR-195
LMR-200
LMR-240
LMR-195
LMR-200
LMR-240
LMR-195
LMR-200
LMR-240
Crimp Die Hex
.213 (5.41) hex
.213 (5.41) hex
.255 (6.48) hex
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
PART NUMBER CRIMP HEX
142-0407-101
142-0407-106
142-4439-101
142-4439-106
142-0435-101
142-0435-106
142-5407-101
142-5407-106
142-0439-101
142-0439-106
142-5435-101
142-5435-106
142-4407-101
142-4407-106
142-5439-101
142-5439-106
142-4435-101
142-4435-106
Flat Punch Dia.
.187 (4.75)
.187 (4.75)
.242 (6.15)
INCHES (MILLIMETERS)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.240 (6.10)
.240 (6.10)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.240 (6.10)
.240 (6.10)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.240 (6.10)
.240 (6.10)