STM32F100RCT6TR STMicroelectronics, STM32F100RCT6TR Datasheet - Page 15

• Manufacturer Part Number: STM32F100RCT6TR
• Description: IC ARM CORTEX MCU 256KB 64LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F100RCT6TR

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 24MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LFQFP
• Core: ARM Cortex M3
• For Use With: STM32100B-EVAL - EVAL BOARD FOR STM32F100VBT6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

STM32F100xC, STM32F100xD, STM32F100xE
2.2.11
2.2.12
2.2.13
2.2.14
The boot loader is located in System Memory. It is used to reprogram the Flash memory by
using USART1. For further details please refer to AN2606.
Power supply schemes
●
●
●
Power supply supervisor
The device has an integrated power on reset (POR)/power down reset (PDR) circuitry. It is
always active, and ensures proper operation starting from/down to 2 V. The device remains
in reset mode when V
external reset circuit.
The device features an embedded programmable voltage detector (PVD) that monitors the
V
generated when V
than the V
message and/or put the MCU into a safe state. The PVD is enabled by software.
Voltage regulator
The regulator has three operation modes: main (MR), low power (LPR) and power down.
●
●
●
This regulator is always enabled after reset. It is disabled in Standby mode, providing high
impedance output.
Low-power modes
The STM32F100xx value line supports three low-power modes to achieve the best
compromise between low power consumption, short startup time and available wakeup
sources:
●
●
DD
/V
V
Provided externally through V
V
RCs and PLL (minimum voltage to be applied to V
used).
V
V
registers (through power switch) when V
MR is used in the nominal regulation mode (Run)
LPR is used in the Stop mode
Power down is used in Standby mode: the regulator output is in high impedance: the
kernel circuitry is powered down, inducing zero consumption (but the contents of the
registers and SRAM are lost)
Sleep mode
In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can
wake up the CPU when an interrupt/event occurs.
Stop mode
Stop mode achieves the lowest power consumption while retaining the content of
SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC
and the HSE crystal oscillators are disabled. The voltage regulator can also be put
DD
SSA
DDA
BAT
DDA
= 2.0 to 3.6 V: External power supply for I/Os and the internal regulator.
, V
= 1.8 to 3.6 V: Power supply for RTC, external clock 32 kHz oscillator and backup
PVD
power supply and compares it to the V
and V
DDA
threshold. The interrupt service routine can then generate a warning
SSA
= 2.0 to 3.6 V: External analog power supplies for ADC, DAC, Reset blocks,
DD
must be connected to V
/V
DD
DDA
is below a specified threshold, V
drops below the V
Doc ID 15081 Rev 5
DD
pins.
DD
DD
PVD
and V
is not present.
PVD
threshold and/or when V
SS
threshold. An interrupt can be
DDA
, respectively.
POR/PDR
is 2.4 V when the ADC or DAC is
, without the need for an
DD
/V
DDA
Description
is higher
15/97