LIS302DLTR STMicroelectronics, LIS302DLTR Datasheet - Page 17
![ACCELEROMETER 3AXIS MEMS 14-LGA](/photos/18/36/183612/14-lga_pkg_sml.jpg)
LIS302DLTR
Manufacturer Part Number
LIS302DLTR
Description
ACCELEROMETER 3AXIS MEMS 14-LGA
Manufacturer
STMicroelectronics
Datasheet
1.STEVAL-MKI006V1.pdf
(42 pages)
Specifications of LIS302DLTR
Featured Product
STM32 Cortex-M3 Companion Products
Axis
X, Y, Z
Acceleration Range
±2.3g, 9.2g
Sensitivity
18mg/digit, 72mg/digit
Voltage - Supply
2.16 V ~ 3.6 V
Output Type
Digital
Bandwidth
100Hz ~ 400Hz Selectable
Interface
I²C, SPI
Mounting Type
Surface Mount
Package / Case
14-LGA
Sensing Axis
X, Y, Z
Acceleration
2 g, 8 g
Digital Output - Number Of Bits
8 bit
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.16 V
Supply Current
0.3 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Digital Output - Bus Interface
I2C, SPI
Shutdown
Yes
For Use With
497-9047 - BOARD DEMO ACCELEROMETER DIL24497-8373 - BOARD EVAL EXTENSION SN250497-8204 - BOARD ADAPTER LIS302SG DIL24497-8203 - BOARD DEMO LIS302SG497-6404 - BOARD EVAL SPZB260 MOD FOR STR9497-6342 - BOARD EVALUATION FOR LIS302DL497-6246 - BOARD EVAL ACCELEROM LIS302ALK497-6227 - BOARD ADAPTER 20DIP LIS3LV02DL497-6226 - BOARD EVAL ACCELEROM LIS3LV02DL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-5911-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LIS302DLTR
Manufacturer:
ST
Quantity:
1 056
Part Number:
LIS302DLTR
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
LIS302DLTR8
Manufacturer:
SONY
Quantity:
26
Part Number:
LIS302DLTR8
Manufacturer:
ST
Quantity:
20 000
LIS302DL
4
4.1
Application hints
Figure 5.
The device core is supplied through Vdd line while the I/O pads are supplied through
Vdd_IO line. Power supply decoupling capacitors (100 nF ceramic, 10 µF Al) should be
placed as near as possible to the pin 6 of the device (common design practice).
All the voltage and ground supplies must be present at the same time to have proper
behavior of the IC (refer to
without blocking the communication busses, in this condition the measurement chain is
powered off.
The functionality of the device and the measured acceleration data is selectable and
accessible through the I
The functions, the threshold and the timing of the two interrupt pins (INT 1 and INT 2) can be
completely programmed by the user though the I
Soldering information
The LGA package is compliant with the ECOPACK®, RoHS and “Green” standard. It is
qualified for soldering heat resistance according to JEDEC J-STD-020C.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendation are available at www.st.com/mems.
Vdd
GND
10uF
100nF
LIS302DL electrical connection
Digital signal from/to signal controller.Signal’s levels are defined by proper selection of Vdd_IO
2
C/SPI interface.When using the I
Figure
8
5). It is possible to remove Vdd maintaining Vdd_IO
6
Top VIEW
2
C/SPI interface.
1
13
2
C, CS must be tied high.
Vdd_IO
Y
DIRECTIONS OF THE
DETECTABLE
ACCELERATIONS
6
TOP VIEW
Application hints
Z
8
1
13
17/42
X