PCF8562TT/2,518 NXP Semiconductors, PCF8562TT/2,518 Datasheet - Page 17
![LCD Drivers LCD DRIVER 32/128SEG](/photos/16/10/161081/sot362_sml.jpg)
PCF8562TT/2,518
Manufacturer Part Number
PCF8562TT/2,518
Description
LCD Drivers LCD DRIVER 32/128SEG
Manufacturer
NXP Semiconductors
Datasheet
1.PCF8562TT2518.pdf
(37 pages)
Specifications of PCF8562TT/2,518
Number Of Digits
16
Number Of Segments
128
Maximum Clock Frequency
400 KHz
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Power Dissipation
400 mW
Maximum Operating Temperature
+ 85 C
Package / Case
TSSOP-48
Maximum Supply Current
20 uA
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935276218518 PCF8562TT/2-T
NXP Semiconductors
PCF8562_5
Product data sheet
7.12 Subaddress counter
7.13 Output bank selector
7.11 Data pointer
The addressing mechanism for the display RAM is realized using the data pointer.
This allows the loading of an individual display data byte, or a series of display data bytes,
into any location of the display RAM. The sequence commences with the initialization of
the data pointer by the load-data-pointer command (see
Following this command, an arriving data byte is stored at the display RAM address
indicated by the data pointer. The filling order shown in
After each byte is stored, the contents of the data pointer is automatically incremented by
a value dependent on the selected LCD drive mode:
If an I
The data pointer should be re-written prior to further RAM accesses.
The storage of display data is determined by the contents of the subaddress counter.
Storage is allowed to take place only when the contents of the subaddress counter agree
with the hardware subaddress applied to A0, A1 and A2. The subaddress counter value is
defined by the device-select command (see
subaddress counter and the hardware subaddress do not agree then data storage is
inhibited but the data pointer is incremented as if data storage had taken place. The
subaddress counter is also incremented when the data pointer overflows.
The hardware subaddress must not be changed while the device is being accessed on the
I
The output bank selector selects one of the four rows per display RAM address for
transfer to the display register. The actual row selected depends on the particular LCD
drive mode in operation and on the instant in the multiplex sequence.
The PCF8562 includes a RAM bank switching feature in the static and 1:2 drive modes. In
the static drive mode, the bank-select command (see
contents of row 2 to be selected for display instead of the contents of row 0. In 1:2 mode,
2
•
•
•
•
C-bus interface.
•
•
•
•
In static drive mode by eight
In 1:2 multiplex drive mode by four
In 1:3 multiplex drive mode by three
In 1:4 multiplex drive mode by two
In 1:4 multiplex mode, all RAM addresses of row 0 are selected, these are followed by
the contents of row 1, row 2 and then row 3.
In 1:3 multiplex mode, row 0, 1 and 2 are selected sequentially
In 1:2 multiplex mode, row 0 and 1 are selected
In static mode, row 0 is selected
2
C-bus data access is terminated early then the state of the data pointer is unknown.
All information provided in this document is subject to legal disclaimers.
Rev. 05 — 19 May 2010
Universal LCD driver for low multiplex rates
Section
7.17). If the contents of the
Section
Figure
Section
7.17) may request the
10.
7.17).
PCF8562
© NXP B.V. 2010. All rights reserved.
17 of 37