TDA8542TS/N1 NXP Semiconductors, TDA8542TS/N1 Datasheet
TDA8542TS/N1
Specifications of TDA8542TS/N1
Available stocks
Related parts for TDA8542TS/N1
TDA8542TS/N1 Summary of contents
Page 1
DATA SHEET TDA8542TS 2 0.7 W BTL audio amplifier Product specification Supersedes data of 1997 Nov 17 File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 1998 Mar 25 ...
Page 2
Philips Semiconductors 2 0.7 W BTL audio amplifier FEATURES Flexibility in use Few external components Low saturation voltage of output stage Gain can be fixed with external resistors Standby mode controlled by CMOS compatible levels Low standby current No switch-on/switch-off ...
Page 3
Philips Semiconductors 2 0.7 W BTL audio amplifier BLOCK DIAGRAM handbook, full pagewidth INL INL n.c. n.c. n.c. n.c. n.c. INR INR SVR MODE BTL/SE 1998 Mar 25 V CCL V CCR CCL 2 R ...
Page 4
Philips Semiconductors 2 0.7 W BTL audio amplifier PINNING SYMBOL PIN DESCRIPTION LGND 1 ground, left channel n.c. 2 not connected OUTL+ 3 positive loudspeaker terminal, left channel MODE 4 operating mode select (standby, mute, operating) SVR 5 half supply ...
Page 5
Philips Semiconductors 2 0.7 W BTL audio amplifier Headphone connection A headphone can be connected to the amplifier using two coupling capacitors for each channel. The common GND pin of the headphone is connected to the ground of the amplifier ...
Page 6
Philips Semiconductors 2 0.7 W BTL audio amplifier DC CHARACTERISTICS amb L SYMBOL PARAMETER V supply voltage CC I quiescent current q I standby current stb ...
Page 7
Philips Semiconductors 2 0.7 W BTL audio amplifier AC CHARACTERISTICS kHz amb L SYMBOL PARAMETER P output power o THD total harmonic distortion ...
Page 8
Philips Semiconductors 2 0.7 W BTL audio amplifier TEST AND APPLICATION INFORMATION Test conditions Because the application can be either Bridge-Tied Load (BTL) or Single-Ended (SE), the curves of each application are shown separately. The thermal resistance = 110 K/W ...
Page 9
Philips Semiconductors 2 0.7 W BTL audio amplifier BTL APPLICATION handbook, full pagewidth Gain left = 2 ------- - R1 R4 Gain right ...
Page 10
Philips Semiconductors 2 0.7 W BTL audio amplifier 10 handbook, halfpage THD (%) 0 dB ...
Page 11
Philips Semiconductors 2 0.7 W BTL audio amplifier 3 handbook, halfpage P (W) 2 ( Fig.10 Worst case power dissipation as a function ...
Page 12
Philips Semiconductors 2 0.7 W BTL audio amplifier SE APPLICATION handbook, full pagewidth Gain left = ------- - R1 R4 Gain right = ...
Page 13
Philips Semiconductors 2 0.7 W BTL audio amplifier 20 handbook, halfpage cs (dB) 40 (1) 60 (2) (3) (4) 80 (5) 100 dB ( ...
Page 14
Philips Semiconductors 2 0.7 W BTL audio amplifier 2.4 handbook, halfpage P (W) (1) 1.6 (2) (3) 0 0.4 0 kHz ...
Page 15
Philips Semiconductors 2 0.7 W BTL audio amplifier handbook, full pagewidth IN1 IN2 1998 Mar 25 a. Top view copper layout GND OUT1 OUT1 100 100 ...
Page 16
Philips Semiconductors 2 0.7 W BTL audio amplifier PACKAGE OUTLINE SSOP20: plastic shrink small outline package; 20 leads; body width 4 pin 1 index 1 e DIMENSIONS (mm are the original dimensions) A UNIT A A ...
Page 17
Philips Semiconductors 2 0.7 W BTL audio amplifier SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, ...
Page 18
Philips Semiconductors 2 0.7 W BTL audio amplifier DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product ...
Page 19
Philips Semiconductors 2 0.7 W BTL audio amplifier 1998 Mar 25 NOTES 19 Product specification TDA8542TS ...
Page 20
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010, ...