AD5722RBREZ Analog Devices Inc, AD5722RBREZ Datasheet - Page 20

• Manufacturer Part Number: AD5722RBREZ
• Description: Dual 12Bit DAC 0.5 LSB INL + 10ppm Ref
• Manufacturer: Analog Devices Inc

Specifications of AD5722RBREZ

• Design Resources: Software Configurable 12-Bit Dual-Channel Unipolar/Bipolar Voltage Output Using AD5722R (CN0091)
• Settling Time: 10µs
• Number Of Bits: 12
• Data Interface: Serial
• Number Of Converters: 2
• Voltage Supply Source: Analog and Digital, Dual ±
• Power Dissipation (max): 190mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP Exposed Pad, 24-eTSSOP, 24-HTSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD5722R/AD5732R/AD5752R
THEORY OF OPERATION
The AD5722R/AD5732R/AD5752R are dual, 12-/14-/16-bit,
serial input, unipolar/bipolar, voltage output DACs. They
operate from unipolar supply voltages of +4.5 V to +16.5 V or
bipolar supply voltages of ±4.5 V to ±16.5 V. In addition, the
parts have software-selectable output ranges of +5 V, +10 V,
+10.8 V, ±5 V, ±10 V, and ±10.8 V. Data is written to the
AD5722R/AD5732R/AD5752R in a 24-bit word format via a
3-wire serial interface. The devices also offer an SDO pin to
facilitate daisy chaining or readback.
The AD5722R/AD5732R/AD5752R incorporate a power-on
reset circuit to ensure that the DAC registers power up loaded
with 0x0000. When powered on, the outputs are clamped to 0 V
via a low impedance path. The parts also feature on-chip
reference and reference buffers.
ARCHITECTURE
The DAC architecture consists of a string DAC followed by an
output amplifier. Figure 44 shows a block diagram of the DAC
architecture. The reference input is buffered before being
applied to the DAC.
The resistor string structure is shown in Figure 45. It is a string
of resistors, each of value R. The code loaded to the DAC register
determines the node on the string where the voltage is to be
tapped off and fed into the output amplifier. The voltage is
tapped off by closing one of the switches connecting the string
to the amplifier. Because it is a string of resistors, it is guaranteed
monotonic.
DAC REGISTER
Figure 44. DAC Architecture Block Diagram
RANGE CONTROL
RESISTOR
REF (–)
REF (+)
STRING
REFIN
GND
OUTPUT
CONFIGURABLE
OUTPUT
AMPLIFIER
V
OUT
Rev. C | Page 20 of 32
x
Output Amplifiers
The output amplifiers are capable of generating both unipolar
and bipolar output voltages. They are capable of driving a load
of 2 kΩ in parallel with 4000 pF to GND. The source and sink
capabilities of the output amplifiers can be seen in Figure 24.
The slew rate is 4.5 V/µs with a full-scale settling time of 10 µs.
Reference Buffers
The AD5722R/AD5732R/AD5752R can operate with either an
external or internal reference. The reference input has an input
range of 2 V to 3 V, with 2.5 V for specified performance. This
input voltage is then buffered before it is applied to the DAC cores.
SERIAL INTERFACE
The AD5722R/AD5732R/AD5752R are controlled over a
versatile 3-wire serial interface that operates at clock rates up to
30 MHz. It is compatible with SPI, QSPI™, MICROWIRE™, and
DSP standards.
Input Shift Register
The input shift register is 24 bits wide. Data is loaded into the
device MSB first as a 24-bit word under the control of a serial
clock input, SCLK. The input register consists of a read/write
bit, three register select bits, three DAC address bits, and 16 data
bits. The timing diagram for this operation is shown in Figure 2.
R
R
R
R
R
REFIN
Figure 45. Resistor String Structure
TO OUTPUT
AMPLIFIER