AD7193BCPZ Analog Devices Inc, AD7193BCPZ Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD7193BCPZ
Manufacturer Part Number
AD7193BCPZ
Description
4ch VeryLow Noise 24Bit SD ADC With PGA
Manufacturer
Analog Devices Inc
Datasheet
1.AD7193BRUZ-REEL.pdf
(56 pages)
Specifications of AD7193BCPZ
Number Of Bits
24
Sampling Rate (per Second)
4.8k
Data Interface
DSP, MICROWIRE™, QSPI™, Serial, SPI™
Number Of Converters
1
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
32-WFQFN, CSP Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD7193
STATUS REGISTER
RS2, RS1, RS0 = 000; Power-On/Reset = 0x80
The status register is an 8-bit read-only register. To access the
ADC status register, the user must write to the communications
register, select the next operation to be a read operation, and
SR7
RDY(1)
Table 19. Status Register (SR) Bit Designations
Bit
Location
SR7
SR6
SR5
SR4
SR3 to SR0
Bit Name
RDY
ERR
NOREF
Parity
CHD3 to CHD0
SR6
ERR(0)
Description
Ready bit for the ADC. This bit is cleared when data is written to the ADC data register. The RDY bit is set
automatically after the ADC data register is read, or a period of time before the data register is updated,
with a new conversion result to indicate to the user that the conversion data should not be read. It is also
set when the part is placed in power-down mode or idle mode or when SYNC is taken low. The end of a
conversion is also indicated by the DOUT/RDY pin. This pin can be used as an alternative to the status
register for monitoring the ADC for conversion data.
ADC error bit. This bit is written to at the same time as the RDY bit. This bit is set to indicate that the result
written to the ADC data register is clamped to all 0s or all 1s. Error sources include overrange, underrange,
or the absence of a reference voltage. This bit is cleared when the result written to the data register
returns to within the allowed analog input range. The ERR bit is also set during calibrations if the reference
source is invalid or if the applied analog input voltages are outside range during system calibrations.
No external reference bit. This bit is set to indicate that the selected reference (REFIN1 or REFIN2) is at a
voltage that is below a specified threshold. When set, conversion results are clamped to all 1s. This bit is
cleared to indicate that a valid reference is applied to the selected reference pins. The NOREF bit is enabled by
setting the REFDET bit in the configuration register to 1.
Parity check of the data register. If the ENPAR bit in the mode register is set and there is an odd number of
1s in the data register, the parity bit is set. It is cleared if there is an even number of 1s in the data register.
The DAT_STA bit in the mode register should be set when the parity check is used. When the DAT_STA bit
is set, the contents of the status register are transmitted along with the data for each data register read.
These bits indicate which channel corresponds to the data register contents. They do not indicate which
channel is presently being converted but indicate which channel was selected when the conversion
contained in the data register was generated.
SR5
NOREF(0)
SR4
Parity(0)
Rev. B | Page 22 of 56
SR3
CHD3(0)
load Bit RS2, Bit RS1, and Bit RS0 with 0. Table 19 outlines the bit
designations for the status register. SR0 through SR7 indicate the
bit locations, SR denoting that the bits are in the status register.
SR7 denotes the first bit of the data stream. The number in paren-
theses indicates the power-on/reset default status of that bit.
SR2
CHD2(0)
SR1
CHD1(0)
SR0
CHD0(0)