ADF4157BRUZ-RL Analog Devices Inc, ADF4157BRUZ-RL Datasheet - Page 19

• Manufacturer Part Number: ADF4157BRUZ-RL
• Description: IC,FREQUENCY SYNTHESIZER,CMOS,TSSOP,16PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Fractional N Synthesizer (RF)r

Specifications of ADF4157BRUZ-RL

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 2:1
• Differential - Input:output: Yes/No
• Frequency - Max: 6GHz
• Divider/multiplier: Yes/Yes
• Voltage - Supply: 2.7 V ~ 3.3 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP
• Frequency-max: 6GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4157EB1Z - BOARD EVALUATION FOR ADF4157
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

FASTLOCK TIMER AND REGISTER SEQUENCES
If the fastlock mode is used, a timer value needs to be loaded into
the PLL to determine the time spent in wide bandwidth mode.
When Bits DB[20:19] in Register 4 (R4) are set to 01 (switched
R fastlock enable), the timer value is loaded via the 12-bit clock
divider value. To use fastlock, the PLL must be written to in the
following sequence:
1.
2.
FASTLOCK: AN EXAMPLE
If a PLL has f
the PLL is set to wide bandwidth for 40 μs.
If the time period set for the wide bandwidth is 40 μs, then
Therefore, 520 must be loaded into the clock divider value in
Register 4 (R4) in Step 2 of the sequence described in the
Fastlock Timer and Register Sequences section.
FASTLOCK: LOOP FILTER TOPOLOGY
To use fastlock mode, an extra connection from the PLL to the
loop filter is needed. The damping resistor in the loop filter must
be reduced to ¼ of its value while in wide bandwidth mode. This is
required because the charge pump current is increased by 16
while in wide bandwidth mode, and stability must be ensured.
During fastlock, the MUXOUT pin (after setting MUXOUT to
fastlock switch by setting Bits DB[30:27] in Register 0 to 1100) is
shorted to ground (this is accomplished by settings Bits DB[20:19]
in Register 4 to 01—switched R fastlock enable). The following
two topologies can be used:
•
•
Use the initialization sequence (see the Initialization
Sequence section) only once after powering up the part.
Load Register 4 (R4) with Bits DB[20:19] set to 01 and the
chosen fastlock timer value (DB18 to DB7). Note that the
duration that the PLL remains in wide bandwidth is equal
to the fastlock timer/f
Fastlock Timer Value = Time in Wide Bandwidth × f
Fastlock Timer Value = 40 μs × 13 MHz = 520
Divide the damping resistor (R1) into two values (R1 and
R1A) that have a ratio of 1:3 (see Figure 22).
Connect an extra resistor (R1A) directly from MUXOUT,
as shown in Figure 23. The extra resistor must be chosen
such that the parallel combination of an extra resistor and
the damping resistor (R1) is reduced to ¼ of the original
value of R1 (see Figure 23).
Figure 22. Fast ock Loop Filter Topology—Topology 1
ADF4157
PFD
MUXOUT
= 13 MHz and a required lock time of 50 μs,
CP
C1
PFD
.
R1
R1A
C2
R2
C3
VCO
PFD
Rev. A | Page 19 of 24
SPUR MECHANISMS
The fractional interpolator in the ADF4157 is a third-order Σ-Δ
modulator (SDM) with a 25-bit fixed modulus (MOD). The
SDM is clocked at the PFD reference rate (f
output frequencies to be synthesized at a channel step resolution of
f
N synthesizers, and how they affect the ADF4157, are discussed in
this section.
Fractional Spurs
In most fractional synthesizers, fractional spurs can appear at
the set channel spacing of the synthesizer. In the ADF4157,
these spurs do not appear. The high value of the fixed modulus
in the ADF4157 makes the Σ-Δ modulator quantization error
spectrum look like broadband noise, effectively spreading the
fractional spurs into noise.
Integer Boundary Spurs
Interactions between the RF VCO frequency and the PFD fre-
quency can lead to spurs known as integer boundary spurs. When
these frequencies are not integer related (which is the purpose
of the fractional-N synthesizer), spur sidebands appear on the
VCO output spectrum at an offset frequency that corresponds
to the beat note or difference frequency between an integer mul-
tiple of the PFD and the VCO frequency.
These spurs are named integer boundary spurs because they are
more noticeable on channels close to integer multiples of the PFD
where the difference frequency can be inside the loop bandwidth.
These spurs are attenuated by the loop filter.
Figure 7 shows an integer boundary spur. The RF frequency is
5800.25 MHz, and the PFD frequency is 25 MHz. The integer
boundary spur is 250 kHz from the carrier at an integer times
the PFD frequency (232 × 25 MHz = 5800 MHz). The spur also
appears on the upper sideband.
Reference Spurs
Reference spurs are generally not a problem in fractional-N
synthesizers because the reference offset is far outside the loop
bandwidth. However, any reference feedthrough mechanism
that bypasses the loop can cause a problem. One such mechanism
is the feedthrough of low levels of on-chip reference switching
noise out through the RF
reference spur levels as high as −90 dBc. Care should be taken in
the PCB layout to ensure that the VCO is well separated from
PFD
/MOD. The various spur mechanisms possible with fractional-
Figure 23. Fastlock Loop Filter Topology—Topology 2
ADF4157
MUXOUT
CP
R1A
IN
C1
x pin back to the VCO, resulting in
R1
C2
R2
PFD
) that allows PLL
C3
ADF4157
VCO