ADSP-21060KS-160 Analog Devices Inc, ADSP-21060KS-160 Datasheet - Page 12

• Manufacturer Part Number: ADSP-21060KS-160
• Description: Digital Signal Processor IC
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Floating Pointr

Specifications of ADSP-21060KS-160

• Supply Voltage Max: 5.25V
• Dsp Type: Fixed / Floating Point
• Mounting Type: Surface Mount
• Package / Case: 240-MQFP
• Memory Organization - Ram: 4M
• Rohs Status: RoHS non-compliant
• Interface: Host Interface, Link Port, Serial Port
• Clock Rate: 40MHz
• Non-volatile Memory: External
• On-chip Ram: 512kB
• Voltage - I/o: 5.00V
• Voltage - Core: 5.00V
• Operating Temperature: 0°C ~ 85°C
• Device Core Size: 32b
• Architecture: Super Harvard
• Format: Floating Point
• Clock Freq (max): 40MHz
• Mips: 40
• Device Input Clock Speed: 40MHz
• Ram Size: 512KB
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 240
• Package Type: MQFP
• Lead Free Status / Rohs Status: Not Compliant

ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 3. Pin Descriptions (Continued)
Pin
TFSx
RFSx
LxDAT3–0
LxCLK
LxACK
EBOOT
LBOOT
BMS
CLKIN
RESET
TCK
TMS
TDI
TDO
TRST
EMU
ICSA
VDD
GND
NC
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
Type
I/O
I/O
I/O
I/O
I/O
I
I
I/OT
I
I/A
I
I/S
I/S
O
I/A
O
O
P
G
Function
Transmit Frame Sync (Serial Ports 0, 1).
Receive Frame Sync (Serial Ports 0, 1).
Link Port Data (Link Ports 0–5). Each LxDAT pin has a 50 k: internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
Link Port Clock (Link Ports 0–5). Each LxCLK pin has a 50 k: internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
Link Port Acknowledge (Link Ports 0–5). Each LxACK pin has a 50 k: internal pull-down resistor that is
enabled or disabled by the LPDRD bit of the LCOM register.
EPROM Boot Select. When EBOOT is high, the ADSP-2106x is configured for booting from an 8-bit EPROM.
When EBOOT is low, the LBOOT and BMS inputs determine booting mode. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
Link Boot. When LBOOT is high, the ADSP-2106x is configured for link port booting. When LBOOT is low,
the ADSP-2106x is configured for host processor booting or no booting. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
Boot Memory Select. Output: Used as chip select for boot EPROM devices (when EBOOT = 1, LBOOT = 0).
In a multiprocessor system, BMS is output by the bus master. Input: When low, indicates that no booting will
occur and that ADSP-2106x will begin executing instructions from external memory. See table below. This
input is a system configuration selection that should be hardwired. *Three-statable only in EPROM boot
mode (when BMS is an output).
EBOOT
1
0
0
0
0
1
Clock In. External clock input to the ADSP-2106x. The instruction cycle rate is equal to CLKIN. CLKIN should
not be halted, changed, or operated below the minimum specified frequency.
Processor Reset. Resets the ADSP-2106x to a known state and begins program execution at the program
memory location specified by the hardware reset vector address. This input must be asserted (low) at
power-up.
Test Clock (JTAG). Provides an asynchronous clock for JTAG boundary scan.
Test Mode Select (JTAG). Used to control the test state machine. TMS has a 20 k: internal pull-up resistor.
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a 20 k: internal pull-up
resistor.
Test Data Output (JTAG). Serial scan output of the boundary scan path.
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low) after power-up or held
low for proper operation of the ADSP-2106x. TRST has a 20 k: internal pull-up resistor.
Emulation Status. Must be connected to the ADSP-2106x EZ-ICE target board connector only.
Reserved, leave unconnected.
Power Supply; nominally 5.0 V dc for 5 V devices or 3.3 V dc for 3.3 V devices. (30 pins).
Power Supply Return. (30 pins).
Do Not Connect. Reserved pins which must be left open and unconnected.
LBOOT
0
0
1
0
1
1
Rev. F | Page 12 of 64 | March 2008
BMS
Output
1 (Input)
1 (Input)
0 (Input)
0 (Input)
x (Input)
Booting Mode
EPROM (Connect BMS to EPROM chip select.)
Reserved
Host Processor
Link Port
No Booting. Processor executes from external memory.
Reserved