DSPIC33FJ16MC304-E/PT Microchip Technology, DSPIC33FJ16MC304-E/PT Datasheet - Page 16

• Manufacturer Part Number: DSPIC33FJ16MC304-E/PT
• Description: 16-bit DSC, 16KB Flash,Motor,40 MIPS,nanoWatt 44 TQFP 10x10x1mm TRAY
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC304-E/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 9x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC33FJ16MC304-E/PTTR; DSPIC33FJ16MC304-E/PTTR

dsPIC33FJ32MC202/204 and dsPIC33FJ16MC304
FIGURE 2-1:
2.2.1
On boards with power traces running longer than six
inches in length, it is suggested to use a tank capacitor
for integrated circuits including DSCs to supply a local
power source. The value of the tank capacitor should
be determined based on the trace resistance that con-
nects the power supply source to the device, and the
maximum current drawn by the device in the applica-
tion. In other words, select the tank capacitor so that it
meets the acceptable voltage sag at the device. Typical
values range from 4.7 µF to 47 µF.
2.3
A low-ESR (<5 Ohms) capacitor is required on the
V
regulator output voltage. The V
connected to V
4.7 µF and 10 µF, 16V connected to ground. The type
can be ceramic or tantalum. Refer to
“Electrical
information.
The placement of this capacitor should be close to the
V
exceed one-quarter inch (6 mm). Refer to
“On-Chip Voltage Regulator”
DS70283H-page 16
CAP
CAP
Ceramic
V
0.1 µF
DD
R
. It is recommended that the trace length not
C
pin, which is used to stabilize the voltage
R1
CPU Logic Filter Capacitor
Connection (V
TANK CAPACITORS
10 Ω
MCLR
V
V
DD
SS
DD
Characteristics”
10 µF
, and must have a capacitor between
RECOMMENDED
MINIMUM CONNECTION
dsPIC33F
Ceramic
0.1 µF
CAP
for details.
)
CAP
pin must not be
for
V
V
DD
Section 24.0
Section 21.2
SS
Ceramic
0.1 µF
Ceramic
0.1 µF
additional
Ceramic
0.1 µF
2.4
The MCLR pin provides for two specific device
functions:
• Device Reset
• Device programming and debugging
During device programming and debugging, the
resistance and capacitance that can be added to the
pin must be considered. Device programmers and
debuggers drive the MCLR pin. Consequently,
specific voltage levels (V
transitions must not be adversely affected. Therefore,
specific values of R and C will need to be adjusted
based on the application and PCB requirements.
For
recommended that capacitor C is isolated from the
MCLR pin during programming and debugging
operations.
Place the components shown in
one-quarter inch (6 mm) from the MCLR pin.
FIGURE 2-2:
Note 1: R ≤ 10 kΩ is recommended. A suggested
example,
2: R1 ≤ 470W will limit any current flowing into
Master Clear (MCLR) Pin
starting value is 10 kΩ. Ensure that the MCLR
pin V
MCLR from the external capacitor C, in the
event of MCLR pin breakdown, due to Elec-
trostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
V
V
IH
DD
R
JP
C
and V
IH
as
and V
IL
shown
EXAMPLE OF MCLR PIN
CONNECTIONS
specifications are met.
R1
© 2011 Microchip Technology Inc.
IL
IH
specifications are met.
and V
MCLR
in
dsPIC33F
IL
Figure
Figure 2-2
) and fast signal
2-2,
within
it
is