KSZ8851-16MQL Micrel Inc, KSZ8851-16MQL Datasheet - Page 12

• Manufacturer Part Number: KSZ8851-16MQL
• Description: Single Ethernet Port + Generic (16-bit) Bus Interface( )
• Manufacturer: Micrel Inc

Specifications of KSZ8851-16MQL

• Controller Type: Ethernet Controller, MAC/PHY
• Interface: Bus
• Voltage - Supply: 1.8V, 2.5V, 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-3292 - BOARD EVALUATION KSZ8851-16MLL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-3253

August 2009
Micrel, Inc.
Pin Number
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Pin Name
P1LED3
PWRDN
VDDCO
DGND
EEDO
DGND
AGND
EECS
ARDY
EEEN
EESK
EEDI
WRN
RDN
AEN
NC
NC
NC
NC
NC
Ipd/O
Type
Opd
Opu
Gnd
Opd
Opd
Gnd
Gnd
Ipu
Ipd
Ipd
Ipu
Ipu
Ipu
—
—
—
—
—
P
Pin Function
Read Strobe Not
Asynchronous read strobe, active Low.
EEPROM Chip Select
This signal is used to select an external EEPROM device.
Asynchronous Ready
ARDY may be used when interfacing asynchronous buses to extend bus access cycles. It
is asynchronous to the host CPU or bus clock. This pin need an external 4.7K pull-up
resistor.
No Connect.
No Connect
Digital IO ground
1.8V regulator output . This 1.8V output pin provides power to pins 38, 43, 57 (VDDA), 63
(VDDAP) and 91 (VDDC) for core VDD supply.
If VDD_IO is set for 1.8V then this pin should be left floating, pins 38, 43, 57 (VDDA), 63
(VDDAP) and 91 (VDDC) will be sourced by the external 1.8V supply that is tied to pins
10, 79, 92, 108 and 125 (VDDIO) with appropriate filtering.
No Connect.
EEPROM Enable
EEPROM is enabled and connected when this pin is pull-up.
EEPROM is disabled when this pin is pull-down or no connect.
Port 1 LED indicator
See the description in pins 3, 4, and 5.
EEPROM Data Out
This pin is connected to DI input of the serial EEPROM.
EEPROM Serial Clock: A 4
(OBCR[1:0]=00 on-chip bus speed @ 125MHz) serial output clock cycle to load
configuration data from the serial EEPROM.
Config Mode: The pull-up/pull-down value is latched as big or little endian mode during
power-up / reset. See “Strapping Options” section for details
EEPROM Data In
This pin is connected to DO output of the serial EEPROM when EEEN is pull-up.
This pin has to pull-down for 8-bit bus mode or pull-up for 16-bus mode when the EEEN
pin is pull-down (without EEPROM).
Config Mode: The pull-up/pull-down value is latched as 16- or 8-bit mode during power-up
/ reset. See “Strapping Options” section for details.
No Connect.
Address Enable
Address and chip select qualifier for the address decoding and chip enable, active Low.
Write Strobe Not
Asynchronous write strobe, active Low.
Digital IO ground
No Connect.
Full-chip power-down. Active Low (Low = Power down; High or floating = Normal
operation). All I/O pins will tri-state during chip power down.
Analog ground
12
μ
s (OBCR[1:0]=11 on-chip bus speed @ 25MHz) or 800ns
KSZ8851-16/32 MQL/MQLI
M9999-083109-2.0