KSZ8851-16MQL Micrel Inc, KSZ8851-16MQL Datasheet - Page 65

• Manufacturer Part Number: KSZ8851-16MQL
• Description: Single Ethernet Port + Generic (16-bit) Bus Interface( )
• Manufacturer: Micrel Inc

Specifications of KSZ8851-16MQL

• Controller Type: Ethernet Controller, MAC/PHY
• Interface: Bus
• Voltage - Supply: 1.8V, 2.5V, 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-3292 - BOARD EVALUATION KSZ8851-16MLL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-3253

Interrupt Status Register (0x92 – 0x93): ISR
This register contains the status bits for all QMU and other interrupt sources.
When the corresponding enable bit is set, it causes the interrupt pin to be asserted.
This register is usually read by the host CPU and device drivers during interrupt service routine or polling. The register
bits are not cleared when read. The user has to write “1” to clear.
August 2009
Micrel, Inc.
Bit
1
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x1
0x1
0x0
0x0
0x0
0x0
0x0
Default Value
Default Value
R/W
RO
RW
R/W
RO
(W1C)
RO
(W1C)
RO
(W1C)
RO
RO
(W1C)
RO
RO
(W1C)
RO
(W1C)
RO
RO
(W1C)
RO
RO
RO
Description
When this bit is set, the wake-up from energy detect interrupt is enabled.
When this bit is reset, the energy detect interrupt is disabled.
Reserved
DEDIE Delay Energy Detect Interrupt Enable
When this bit is set, the delay energy detect interrupt is enabled.
When this bit is reset, the delay energy detect interrupt is disabled.
Note: the delay energy detect interrupt till device is ready for host access.
Description
LCIS Link Change Interrupt Status
When this bit is set, it indicates that the link status has changed from link up to link down,
or link down to link up.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
TXIS Transmit Interrupt Status
When this bit is set, it indicates that the TXQ MAC has transmitted at least a frame on the
MAC interface and the QMU TXQ is ready for new frames from the host.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
RXIS Receive Interrupt Status
When this bit is set, it indicates that the QMU RXQ has received at least a frame from the
MAC interface and the frame is ready for the host CPU to process.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
Reserved
RXOIS Receive Overrun Interrupt Status
When this bit is set, it indicates that the Receive Overrun status has occurred.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
Reserved
TXPSIS Transmit Process Stopped Interrupt Status
When this bit is set, it indicates that the Transmit Process has stopped.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
RXPSIS Receive Process Stopped Interrupt Status
When this bit is set, it indicates that the Receive Process has stopped.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
Reserved
TXSAIS Transmit Space Available Interrupt Status
When this bit is set, it indicates that Transmit memory space available status has
occurred.
When this bit is reset, the Transmit memory space available interrupt is disabled.
RXWFDIS Receive Wakeup Frame Detect Interrupt Status
When this bit is set, it indicates that Receive wakeup frame detect status has occurred.
Write “1000” to PMECR[5:2] to clear this bit
RXMPDIS Receive Magic Packet Detect Interrupt Status
When this bit is set, it indicates that Receive magic packet detect status has occurred.
Write “0100” to PMECR[5:2] to clear this bit.
LDIS Linkup Detect Interrupt Status
65
KSZ8851-16/32 MQL/MQLI
M9999-083109-2.0