LAN9218I-MT SMSC, LAN9218I-MT Datasheet - Page 94
![Ethernet ICs Indust Hi Perfrm Single-Chip](/photos/27/13/271361/lan9218i_sml.jpg)
LAN9218I-MT
Manufacturer Part Number
LAN9218I-MT
Description
Ethernet ICs Indust Hi Perfrm Single-Chip
Manufacturer
SMSC
Type
Single Chip MAC and PHY Controllerr
Datasheet
1.LAN9218I-MT.pdf
(133 pages)
Specifications of LAN9218I-MT
Ethernet Connection Type
10 Base-T, 100 Base-TX
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Number Of Transceivers
1
Standard Supported
802.3, 802.3u
Data Rate
10 Mbps, 100 Mbps
Supply Voltage (max)
3.3 V
Supply Voltage (min)
0 V
Supply Current (max)
69 mA
Maximum Operating Temperature
+ 85 C
Package / Case
TQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9218I-MT
Manufacturer:
Standard
Quantity:
1 981
Company:
Part Number:
LAN9218I-MT
Manufacturer:
SMSC
Quantity:
6
Part Number:
LAN9218I-MT
Manufacturer:
SMSC
Quantity:
20 000
Revision 2.7 (03-15-10)
5.4.1
30-24
BITS
31
23
22
21
20
19
18
17
16
15
14
Receive All Mode (RXALL). When set, all incoming packets will be received and passed on to the
address filtering Function for processing of the selected filtering mode on the received frame. Address
filtering then occurs and is reported in Receive Status. When reset, only frames that pass Destination
Address filtering will be sent to the Application.
Reserved
Disable Receive Own (RCVOWN). When set, the MAC disables the reception of frames when the
MII TX_EN signal is asserted. The MAC blocks the transmitted frame on the receive path. When reset,
the MAC receives all packets the PHY gives, including those transmitted by the MAC.This bit should
be reset when the Full Duplex Mode bit is set.
Reserved
Loopback operation Mode (LOOPBK). Selects the loop back operation modes for the MAC. This is
only for full duplex mode
1’b0: Normal: No feedback
1’b1: Internal: Through MII
In internal loopback mode, the TX frame is received by the Internal MII interface, and sent back to
the MAC without being sent to the PHY.
Note:
Full Duplex Mode (FDPX). When set, the MAC operates in Full-Duplex mode, in which it can transmit
and receive simultaneously. In Full-Duplex mode, the heartbeat check is disabled and the heartbeat
fail status should thus be ignored.
Pass All Multicast (MCPAS). When set, indicates that all incoming frames with a Multicast destination
address (first bit in the destination address field is 1) are received. Incoming frames with physical
address (Individual Address/Unicast) destinations are filtered and received only if the address matches
the MAC Address.
Promiscuous Mode (PRMS). When set, indicates that any incoming frame is received regardless of
its destination address.
Inverse filtering (INVFILT). When set, the address check Function operates in Inverse filtering mode.
This is valid only during Perfect filtering mode.
Pass Bad Frames (PASSBAD). When set, all incoming frames that passed address filtering are
received, including runt frames and collided frames.
Hash Only Filtering mode (HO). When set, the address check Function operates in the Imperfect
Address Filtering mode both for physical and multicast addresses
Reserved
MAC_CR—MAC Control Register
This register establishes the RX and TX operation modes and controls for address filtering and packet
filtering.
Offset:
Default Value:
When enabling or disabling the loopback mode it can take up to 10μs for the mode change
to occur. The transmitter and receiver must be stopped and disabled when modifying the
LOOPBK bit. The transmitter or receiver should not be enabled within10μs of modifying the
LOOPBK bit.
High-Performance Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX and Industrial Temperature Support
1
00040000h
DATASHEET
DESCRIPTION
94
Attribute:
Size:
R/W
32 bits
SMSC LAN9218i
Datasheet