UBA2021T/N2 NXP Semiconductors, UBA2021T/N2 Datasheet - Page 7

• Manufacturer Part Number: UBA2021T/N2
• Description: CFL Lamp DRVR 14-Pin SO Tube
• Manufacturer: NXP Semiconductors

Specifications of UBA2021T/N2

• Package: 14SO
• Driver Type: CFL Lamp
• Module Configuration: Half Bridge
• Supply Current: 1mA
• Meter Display Type: Fluorescent Lamp
• Supply Voltage Range: 9.55V To 10.75V, 11.35V To 12.55V
• Driver Case Style: SOIC
• No. Of Pins: 14
• Operating: RoHS Compliant
• Operating Supply Voltage: 630 V
• Maximum Operating Temperature: + 150 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC-14
• Minimum Operating Temperature: - 40 C
• Lead Free Status / Rohs Status: Details

NXP Semiconductors
8. Limiting values
UBA2021_4
Product data sheet
7.12 Frequency and change in frequency
7.13 Ground pins
7.14 Charge coupling
At any point in time during oscillation, the circuit will operate between f
change in frequency will be gradual, no steps in frequency will occur. Changes in
frequency caused by a change in voltage at the CI-pin show a rather constant f/ t over
the entire frequency range. The following rates are realized (at a frequency of 85 kHz and
with a 100 nF capacitor connected to the PCI-pin):
The PGND-pin is the ground reference of the IC with respect to the application. As an
exception the SGND-pin provides a local ground reference for the components connected
to the CP-pin, CI-pin, RREF-pin and thee CF-pin. For this purpose the PGND-pin and
SGND-pin are short circuited internally. External connection of the PGND-pin and the
SGND-pin is not preferred. The sum of currents flowing out of the CP-pin, CI-pin,
RREF-pin, CF-pin and the SGND-pin must remain zero at all time.
Due to parasitic capacitive coupling to the high voltage circuitry, all pins are burdened with
a repetitive charge injection. Given the typical application in
the CF-pin are sensitive to this charge injection. For the rating Q
operation of the IC is guaranteed, independent of the current level. Charge coupling at
current levels below 50 mA will not interfere with the accuracy of the V
levels. Charge coupling at current levels below 20 mA will not interfere with the accuracy
of any parameter.
Table 5.
In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages referenced to
ground.
Symbol
V
I
V
SR
P
T
T
VS(clamp)
•
•
•
amb
j
FS
RS
For any increase in frequency: f/ t is between 15 kHz/ms and 37.5 kHz/ms.
During preheat and normal operation: f/ t for a decrease in frequency is between
During the ignition phase: f/ t for a decrease in frequency is between
6 kHz/ms and 15 kHz/ms.
150 Hz/ms and 375 Hz/ms.
Limiting values
Parameter
high side floating supply
voltage
clamp current
input voltage pin RS
slew rate at pins S1, G1
and FS (with respect to
ground)
power dissipation
ambient temperature
junction temperature
Rev. 04 — 25 July 2008
Conditions
operating
t
transient of 50 ns
0.5 s
630 V driver IC for CFL and TL lamps
Figure
Min
-
-
-
-
2.5
15
4
40
40
couple
7, the RREF-pin and
UBA2021
a safe functional
RS(cap)
B
© NXP B.V. 2008. All rights reserved.
Max
570
630
35
+2.5
+2.5
+4
500
+150
+150
and f
and V
start
. Any
Unit
V
V
mA
V
V
V/ns
mW
RS(ctrl)
C
C
7 of 16