ISP1505ABS NXP Semiconductors, ISP1505ABS Datasheet - Page 23
![RF Transceiver USB2.0/ULPI1.1 XCVR](/photos/15/65/156570/sot616_sml.jpg)
ISP1505ABS
Manufacturer Part Number
ISP1505ABS
Description
RF Transceiver USB2.0/ULPI1.1 XCVR
Manufacturer
NXP Semiconductors
Datasheet
1.ISP1505ABS557.pdf
(76 pages)
Specifications of ISP1505ABS
Number Of Receivers
5
Number Of Transmitters
4
Operating Supply Voltage
3 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
HVQFN-24
Maximum Data Rate
480 Mbps
Maximum Supply Current
0.001 mA, 48 mA
Minimum Operating Temperature
- 40 C
Protocol Supported
USB 2.0
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ISP1505ABS,557
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1505ABS
Manufacturer:
NXP
Quantity:
13
NXP Semiconductors
Table 8.
ISP1505A_ISP1505C_3
Product data sheet
Command
type name
Idle
Packet
transmit
Register
write
Register
read
TXCMD byte format
Command code
DATA[7:6]
00b
01b
10b
11b
9.5.1 TXCMD
9.5.2 RXCMD
9.5 TXCMD and RXCMD
The FAULT input pin is mapped to the A_VBUS_VLD bit in RXCMD. Any changes for the
FAULT input will trigger RXCMD carrying the FAULT condition with A_VBUS_VLD.
Commands between the ISP1505 and the link are described in the following subsections.
By default, the link must drive the ULPI bus to its idle state of 00h. To send commands and
USB packets, the link drives a nonzero value on DATA[7:0] to the ISP1505 by sending a
byte called TXCMD. Commands include USB packet transmissions, and register reads
and writes. Once the TXCMD is interpreted and accepted by the ISP1505, the NXT signal
is asserted and the link can follow up with the required number of data bytes. The TXCMD
byte format is given in
result in undefined behavior.
Various TXCMD packet and register sequences are shown in later sections.
The ISP1505 communicates status information to the link by asserting DIR and sending
an RXCMD byte on the data bus. The RXCMD data byte format is given in
The ISP1505 will automatically send an RXCMD whenever there is a change in any of the
RXCMD data fields. The link must be able to accept an RXCMD at any time; including
single RXCMDs, back-to-back RXCMDs, and RXCMDs at any time during USB receive
packets when NXT is LOW. An example is shown in
refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1 .
An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt
condition is removed before exiting.
Command
payload DATA[5:0]
00 0000b
00 0000b
00 XXXXb
10 1111b
XX XXXXb
10 1111b
XX XXXXb
Rev. 03 — 26 August 2008
Table
Command
name
NOOP
NOPID
PID
EXTW
REGW
EXTR
REGR
8. Any values other than those in
Command description
No operation. 00h is the idle value of the data bus. The
link must drive NOOP by default.
Transmit USB data that does not have a PID, such as
chirp and resume signaling. The ISP1505 starts
transmitting only after accepting the next data byte.
Transmit USB packet. DATA[3:0] indicates USB packet
identifier PID[3:0].
Extended register write command (optional). The 8-bit
address must be provided after the command is
accepted.
Register write command with 6-bit immediate address.
Extended register read command (optional). The 8-bit
address must be provided after the command is
accepted.
Register read command with 6-bit immediate address.
ULPI HS USB host and peripheral transceiver
ISP1505A; ISP1505C
Figure
6. For details and diagrams,
Table 8
are illegal and may
© NXP B.V. 2008. All rights reserved.
Table
9.
22 of 75