IDT77V107L25PFI8 IDT, Integrated Device Technology Inc, IDT77V107L25PFI8 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT77V107L25PFI8
Manufacturer Part Number
IDT77V107L25PFI8
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT77V107L25PFI8.pdf
(24 pages)
Specifications of IDT77V107L25PFI8
Data Rate
25.6/51.2Mbps
Number Of Channels
1
Type Of Atm Phy Interface
UTOPIA
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Pin Count
100
Mounting
Surface Mount
Lead Free Status / RoHS Status
Not Compliant
Transmission Description
Refer to Figure 4 on the previous page. Cell transmission begins with
the PHY-ATM Interface. An ATM layer device transfers a cell into the
77V107 across the Utopia transmit bus. This cell enters a 3-cell deep
transmit FIFO. Once a complete cell is in the FIFO, transmission begins
by passing the cell, four bits (MSB first) at a time to the 'Scrambler'.
against the 4 high order bits (X(t), X(t-1), X(t-2), X(t-3)) of a 10 bit
pseudo-random nibble generator (PRNG). Its function is to provide the
appropriate frequency distribution for the signal across the line.
whether the processed nibble is part of a data or command byte. Note
however that only data nibbles are scrambled. The entire command byte
(X _C) is NOT scrambled before it's encoded (see diagram for illustra-
tion). The PRNG is based upon the following polynomial:
be generated from the following equations:
X(t+1).
time an X_X command is sent. An X_X command is initiated only at the
beginning of a cell transfer after the PRNG has cycled through all of its
states (2
after power on will also be accompanied with an X_X command byte.
Each time an X_X command byte is sent, the first nibble after the last
escape (X) nibble is XOR'd with 1111b (PRNG = 3FFx).
possibility of a reset PRNG start-of-cell command and a timing marker
command occurring consecutively does exist (e.g. X_X_X_8). In this
case, the detection of the last two consecutive escape (X) nibbles will
cause the PRNG to reset to its initial 3FFx state. Therefore, the PRNG is
clocked only after the first nibble of the second consecutive escape pair.
nibbles are further encoded using a 4b/5b process. The 4b/5b scheme
ensures that an appropriate number of signal transitions occur on the
line. A total of seventeen 5-bit symbols are used to represent the sixteen
4-bit data nibbles and the one escape (X) nibble. The table below lists
the 4-bit data with their corresponding 5-bit symbols:
IDT77V107
The 'Scrambler' takes each nibble of data and exclusive-ORs them
The PRNG is clocked every time a nibble is processed, regardless of
X
With this polynomial, the four output data bits (D3, D2, D1, D0) will
D3 = d3 xor X(t-3)
D2 = d2 xor X(t-2)
D1 = d1 xor X(t-1)
D0 = d0 xor X(t)
The following nibble is scrambled with X(t+4), X(t+3), X(t+2), and
A scrambler lock between the transmitter and receiver occurs each
Because a timing marker command (X_8) may occur at any time, the
Once the data nibbles have been scrambled using the PRNG, the
10
+ X
10
7
- 1 = 1023 states). The first valid ATM data cell transmitted
+ 1
6 of 24
properties. Among them is the fact that the output data bits can be
represented by a set of relatively simple symbols;
whether a timing marker command (X_8) or a start-of-cell command
was sent (X_X or X_4). If a start-of-cell command is detected, the next
53 bytes received are decoded and forwarded to the descrambler. (See
the TC Receive Block Diagram).
encoder. The NRZI code transitions the wire voltage each time a '1' bit is
sent. This, together with the previous encoding schemes guarantees
that long run lengths of either '0' or '1's are prevented. Each symbol is
shifted out with its most significant bit sent first.
active by continuing to transmit valid symbols. But it does not transmit
another start-of-cell command until it has another cell for transmission.
The 77V107 never creates its own idle cells for transmission.
Transmit HEC Byte Calculation/Insertion
lated automatically across the first 4 bytes of the cell header, depending
upon the setting of bit 5 of the LED Driver and HEC Status/Control
Register (0x03). This byte is then either inserted as a replacement of the
fifth byte transferred to the PHY by the external system, or the cell is
transmitted as received. A third operating mode provides for insertion of
"Bad" HEC codes which may aid in communication diagnostics. These
modes are controlled by the LED Driver and HEC Status/Control Regis-
ters.
Receiver Description
but in reverse. The data is NRZI decoded before each symbol is reas-
sembled. The symbols are then sent to the 5b/4b decoder, followed by
the Command Byte Interpreter, De-Scrambler, and finally through a
FIFO to the UTOPIA interface to an ATM Layer device.
This encode/decode implementation has several very desirable
On the receiver, the decoder determines from the received symbols
The output of the 4b/5b encoder provides serial data to the NRZI
When no cells are available to transmit, the 77V107 keeps the line
Byte #5 of each ATM cell, the HEC (Header Error Control) is calcu-
The receiver side of the TC sublayer operates like the transmitter,
!
!
Run length is limited to <= 5;
Disparity never exceeds +/- 1.
ESC(X) = 00010
0010
0110
1010
1110
Data
Data
0000
0100
1000
1100
Symbol
Symbol
01010
01110
11010
11110
10101
00111
10010
10111
0001
0101
1001
1101
Data
0011
0111
1011
1111
Data
Symbol
Symbol
01001
01101
11001
11101
01011
01111
11011
11111
December 2004
3505 drw 05a
.
.