IDT77V1254L25PG IDT, Integrated Device Technology Inc, IDT77V1254L25PG Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT77V1254L25PG
Manufacturer Part Number
IDT77V1254L25PG
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT77V1254L25PG.pdf
(48 pages)
Specifications of IDT77V1254L25PG
Data Rate
25.6/51.2Mbps
Number Of Channels
4
Type Of Atm Phy Interface
DPI/UTOPIA
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Pin Count
144
Mounting
Surface Mount
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT77V1254L25PGI
Manufacturer:
IDT
Quantity:
28
Company:
Part Number:
IDT77V1254L25PGI
Manufacturer:
IDT
Quantity:
621
encoder. The NRZI code transitions the wire voltage each time a '1' bit is
sent. This, together with the previous encoding schemes guarantees
that long run lengths of either '0' or '1's are prevented. Each symbol is
shifted out with its most significant bit sent first.
line active by continuing to transmit valid symbols. But it does not
transmit another start-of-cell command until it has another cell for trans-
mission. The 77V1254L25 never generates idle cells.
lated automatically across the first 4 bytes of the cell header, depending
upon the setting of bit 5 of registers 0x03, 0x13, 0x23 and 0x33. This
byte is then either inserted as a replacement of the fifth byte transferred
to the PHY by the external system, or the cell is transmitted as received.
A third operating mode provides for insertion of
"Bad" HEC codes which may aid in communication diagnostics. These
modes are controlled by the LED Driver and HEC Status/Control Regis-
ters.
in reverse. The data is NRZI decoded before each symbol is reassem-
bled. The symbols are then sent to the 5b/4b decoder, followed by the
Command Byte Interpreter, De-Scrambler, and finally through a FIFO to
the UTOPIA or DPI interface to an ATM Layer device.
errors, it does not attempt to correct them.
symbol-synchronized. When not symbol-synchronized, the receiver will
indicate a significant number of bad symbols, and will deassert the Good
Signal Bit as described below. Synchronization is established immedi-
ately once that port receives an Escape symbol, usually as part of the
start-of-cell command byte preceding the first received cell.
interrupt if the line is deemed 'bad'. The Interrupt Status Registers
IDT77V1254L25
The output of the 4b/5b encoder provides serial data to the NRZI
When no cells are available to transmit, the 77V1254L25 keeps the
Transmit HEC Byte Calculation/Insertion
Byte #5 of each ATM cell, the HEC (Header Error Control) is calcu-
Receiver Description
The receiver side of the TC sublayer operates like the transmitter, but
ATM Cell Format
Note that although the IDT77V1254L25 can detect symbol and HEC
Upon reset or the re-connect, each port's receiver is typically not
The IDT77V1254L25 monitors line conditions and can provide an
UDF = User Defined Field (or HEC)
Bit 7
Payload Byte 48
Payload Byte 1
Header Byte 1
Header Byte 2
Header Byte 3
Header Byte 4
UDF
Bit 0
3505 drw 52
.
14 of 48
(registers 0x01, 0x11, 0x21 and 0x31) contain a Good Signal Bit (bit 6,
set to 0 = Bad signal initially) which shows the status of the line per the
following algorithm:
down counter that counts from 7 to 0 and is initially set to 7. When the
clock ticks for 1,024 cycles (32MHz clock, 1,024 cycles = 204.8
symbols) and no "bad symbol" has been received, the counter
decreases by one. However, if at least one "bad symbol" is detected
during these 1,024 clocks, the counter is increased by one, to a
maximum of 7. The Good Signal Bit is set to 1 when this counter
reaches 0. The Good Signal Bit could be set to 1 as quickly as 1,433
symbols (204.8 x 7) if no bad symbols have been received.
down counter counts from 0 to 7 (being at 0 to provide a "Good" status).
When the clock ticks for 1,024 cycles (32MHz clock, 1,024 cycles =
204.8 symbols) and there is at least one "bad symbol", the counter
increases by one. If it detects all "good symbols" and no "bad symbols"
in the next time period, the counter decreases by one. The "Bad Signal"
is declared when the counter reaches 7. The Good Signal Bit could be
set to 0 as quickly as 1,433 symbols (204.8 x 7) if at least one "bad
symbol" is detected in each of seven consecutive groups of 204.8
symbols.
feature which is essential for some applications requiring synchroniza-
tion for voice or video, and unnecessary for other applications. Figure 7
shows the options available for generating and receiving the 8kHz
timing marker.
TXREF Control Register (0x40). Each port is individually programmable
to either a local source or a looped remote source. The local source is
TXREF, which is an 8kHz clock of virtually any duty cycle. When
unused, TXREF should be tied high. Also note that it is not limited to
8kHz, should a different frequency be desired. When looped, a received
X_8 command byte causes one to be generated on the transmit side.
negative pulse on RXREF. The source channel of the marker is
programmable.
PHY-ATM Interface
layer devices such as segmentation and reassembly (SAR) and
switching chips. MODE[1:0] are used to select the configuration of this
interface, as shown in the table below.
the ATM Forum. It has separate transmit and receive channels and
specific handshaking protocols. UTOPIA Level 2 has dedicated address
signals for both the transmit and receive directions that allow the ATM
layer device to specify with which of the four PHY channels it is commu-
nicating. UTOPIA Level 1 does not have address signals.
To declare 'Good Signal' (from "Bad" to "Good") There is an up-
To declare 'Bad Signal' (from "Good" to "Bad") The same up-
8kHz Timing Marker
The 8kHz timing marker, described earlier, is a completely optional
The source of the marker is programmable in the RXREF and
A received X_8 command byte causes the 77V1254L25 to issue a
The 77V1254L25 PHY offers three choices in interfacing to ATM
UTOPIA is a Physical Layer to ATM Layer interface standardized by
December 2004