SC16C554BIBS-F NXP Semiconductors, SC16C554BIBS-F Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
SC16C554BIBS-F
Manufacturer Part Number
SC16C554BIBS-F
Description
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C554BIBS-F.pdf
(58 pages)
Specifications of SC16C554BIBS-F
Transmit Fifo
16Byte
Receive Fifo
16Byte
Transmitter And Receiver Fifo Counter
Yes
Data Rate
5Mbps
Operating Supply Voltage (max)
5.5V
Mounting
Surface Mount
Pin Count
48
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Compliant
NXP Semiconductors
Table 2.
[1]
SC16C554B_554DB
Product data sheet
Symbol
TXA
TXB
TXC
TXD
TXRDY
V
XTAL1
XTAL2
CC
HVQFN48 package die supply ground is connected to both GND pins and exposed center pad. GND pins must be connected to supply
ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be
soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias
need to be incorporated in the PCB in the thermal pad region.
Pin description
Pin
PLCC68 LQFP64 LQFP80 HVQFN48
17
19
51
53
39
13, 30,
47, 64
35
36
8
10
39
41
-
4, 21,
35, 52
25
26
…continued
29
32
69
72
55
5, 25,
45, 65
50
51
All information provided in this document is subject to legal disclaimers.
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
6
8
32
34
-
2, 28
18
19
Rev. 4 — 8 June 2010
Type
O
O
O
O
O
I
I
O
Description
Transmit data A, B, C, D. These outputs are
associated with individual serial transmit channel data
from the SC16C554B/554DB. The TX signal will be a
logic 1 during reset, idle (no data), or when the
transmitter is disabled. During the local Loopback
mode, the TXn output pin is disabled and TX data is
internally connected to the UART RX input.
Transmit Ready (active LOW). TXRDY contains the
wire-ORed status of all four transmit channel FIFOs,
TXRDYA to TXRDYD. A logic 0 indicates a buffer ready
status, that is, at least one location is empty and
available in one of the TX channels (A to D). This pin
goes to a logic 1 when all four channels have no more
empty locations in the TX FIFO or THR. Individual
channel TX status can be read by examining individual
internal registers via CS and A0 to A4 pin functions.
The TXRDY pin is not available on the HVQFN48
package.
Power supply inputs.
Crystal or external clock input. Functions as a crystal
input or as an external clock input. A crystal can be
connected between this pin and XTAL2 to form an
internal oscillator circuit (see
an external clock can be connected to this pin to
provide custom data rates. (See
“Programmable baud rate
Output of the crystal oscillator or buffered clock.
(See also XTAL1.) Crystal oscillator output or buffered
clock output.
SC16C554B/554DB
generator”.)
Figure
Section 6.6
© NXP B.V. 2010. All rights reserved.
13). Alternatively,
14 of 58