935276246518 NXP Semiconductors, 935276246518 Datasheet - Page 74

• Manufacturer Part Number: 935276246518
• Manufacturer: NXP Semiconductors

Specifications of 935276246518

• Screening Level: Industrial
• Package Type: HBGA
• Pin Count: 156
• Lead Free Status / RoHS Status: Compliant

NXP Semiconductors
Table 29.
[1]
[2]
SAF7118_4
Product data sheet
Blanking
period
...
The generation of the timing reference codes can be suppressed by setting OFTS[2:0] to 010; see
sequence is replaced by the standard ‘- 80 - 10 -’ blanking values.
If raw samples or sliced data are selected by the line control registers (LCR2 to LCR24), the Y samples are replaced by CVBS samples.
80
10
Data format on the expansion port
Timing reference
code (Hex)
FF 00 00 SAV C
The relationship of LCR programming to line numbers is described in
Figure 30
The data type selections by LCR are overruled by setting OFTS2 = 1 (subaddress 13h
bit D2). This setting is mainly intended for device production test. The VPO-bus carries the
upper or lower 8 bits of the two ADCs depending on the OFTS[1:0] 13h[1:0] settings; see
Table
a Y/C mode is selected, the expansion port carries the multiplexed output signals of both
ADCs, and in CVBS mode the output of only one ADC. No timing reference codes are
generated in this mode.
Remark: The LSBs (bit D0) of the ADCs are also available on pin RTS0; see
The SAV/EAV timing reference codes define the start and end of valid data regions. The
ITU-blanking code sequence ‘- 80 - 10 - 80 - 10 -...’ is transmitted during the horizontal
blanking period between EAV and SAV.
The position of the F-bit is constant in accordance with ITU 656;
see
The V-bit can be generated in two different ways (see
via OFTS1 and OFTS0; see
The F and V bits change synchronously with the EAV code.
•
[1]
– Adaptive luminance comb filter, peaking and chrominance trap are bypassed within
This data type is defined for future enhancements. It could be activated for lines
containing standard test signals within the vertical blanking period. Currently the most
sources do not contain test lines. The nominal levels are illustrated in
Raw samples (data types 0 to 5 and 7 to 14): C
type 6, but CVBS samples are transferred instead of processed luminance samples
within the Y time slots.
The amplitude and offset of the CVBS signal is programmable via RAWG7 to RAWG0
and RAWO7 to RAWO0; see
are illustrated in
Table 31
58. The input configuration is done via MODE[5:0] 02h[5:0] settings; see
the luminance processing
720 pixels Y-C
and
B
0 Y0 C
and
Figure
Table
Figure
R
31.
0 Y1 C
B
32.
Rev. 04 — 4 July 2008
-C
R
20.
4 : 2 : 2 data
Table
B
Multistandard video decoder with adaptive comb filter
2 Y2 ... C
Section
58.
[2]
10,
R
Table 63
718 Y719 FF 00 00 EAV 80
B
-C
Table 31
and
R
samples are similar to data
Timing reference
code (Hex)
Table
Table
and
64. The nominal levels
58. In this event the code
Table
[1]
Section
SAF7118
© NXP B.V. 2008. All rights reserved.
32) controlled
Figure
Blanking
period
Table
8.3,
Table
19.
10
74 of 175
56.
40. If
...