MC34910G5ACR2 Freescale, MC34910G5ACR2 Datasheet - Page 31
![](/photos/31/26/312678/296-32-tqfp_sml.jpg)
MC34910G5ACR2
Manufacturer Part Number
MC34910G5ACR2
Description
Manufacturer
Freescale
Datasheet
1.MC34910G5ACR2.pdf
(90 pages)
Specifications of MC34910G5ACR2
Turn Off Delay Time
10us
Number Of Drivers
2
Operating Temperature (min)
-40C
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC34910G5ACR2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
RST Wake-up
RST pin is held low long enough to pass the internal glitch
filter. Then, the 33910 will change to Normal Request or
Normal modes depending on the WDCONF pin
configuration. The RST wake-up does not generate an
interrupt and is not reported via SPI.
configured:
configured:
WINDOW WATCHDOG
which is active in Normal mode. The watchdog can be
configured by an external resistor connected to the WDCONF
pin. The resistor is used to achieve higher precision in the
timebase used for the watchdog.
MOD bits of the Mode Control Register (MCR).
not allowed, but after the first half of the SPI timeout window,
the clear operation opens. If a clear operation is performed
outside the window, the 33910 will reset the MCU, in the
same way as when the watchdog overflows.
Analog Integrated Circuit Device Data
Freescale Semiconductor
While in Stop mode, the 33910 can wake-up when the
From Stop mode, the following wake-up events can be
• Wake-up from L1 input without cyclic sense
• Cyclic sense wake-up inputs
• Force wake-up
• CS wake-up
• LIN wake-up
• RST wake-up
From Sleep mode, the following wake-up events can be
• Wake-up from L1 input without cyclic sense
• Cyclic sense wake-up inputs
• Force wake-up
• LIN wake-up
The 33910 includes a configurable window watchdog
SPI clears are performed by writing through the SPI in the
During the first half of the SPI timeout, watchdog clears are
must connect the WDCONF pin to ground. This measure
effectively disables Normal Request mode. The WDOFF bit
in the Watchdog Status Register (WDSR) will be set. This
condition is only detected during Reset mode.
the watchdog falls back to the internal lower precision
timebase of 150 ms (typ.) and signals the faulty condition
through the Watchdog Status Register (WDSR).
prescaler which can be configured by the Timing Control
Register (TIMCR). During Normal Request mode, the
window watchdog is not active but there is a 150 ms (typ.)
timeout for leaving the Normal Request mode. In case of a
timeout, the 33910 will enter into Reset mode, resetting the
microcontroller before entering again into Normal Request
mode.
FAULTS DETECTION MANAGEMENT
or under-voltage on VS1, TxD in permanent Dominant State,
Over-temperature on HS, LIN. It is able to take corrective
actions accordingly. Most of faults are monitoring through
SPI and the Interrupt pin. The microcontroller can also take
actions.
device is able to detect with associated conditions. The status
for a device recovery and the SPI or pins monitoring are also
described.
To disable the watchdog function in Normal mode the user
If neither a resistor nor a connection to ground is detected,
The watchdog timebase can be further divided by a
The 33910 has the capability to detect faults like an over
The following table summarizes all fault sources the
WD TIMING X 50%
NO WATCHDOG CLEAR
Figure 15. Window Watchdog Operation
WINDOW CLOSED
WD TIMING SELECTED BY RESISTOR
ALLOWED
ON WDCONF PIN
WD PERIOD (t
FUNCTIONAL DEVICE OPERATIONS
PWD
WD TIMING X 50%
FOR WATCHDOG
OPERATIONAL MODES
WINDOW OPEN
)
CLEAR
33910
31