MC9S08AW60CFGE Freescale, MC9S08AW60CFGE Datasheet - Page 61

• Manufacturer Part Number: MC9S08AW60CFGE
• Manufacturer: Freescale

Specifications of MC9S08AW60CFGE

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 34
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 60KB
• Lead Free Status / RoHS Status: Compliant

4.6.6
Only five command codes are recognized in normal user modes as shown in
Section 4.4.3, “Program and Erase Command
programming and erase operations.
Freescale Semiconductor
FACCERR
FBLANK
FPVIOL
Reset
FCBEF
FCCF
Field
7
6
5
4
2
W
R
FLASH Command Register (FCMD)
FCMD7
FLASH Command Buffer Empty Flag — The FCBEF bit is used to launch commands. It also indicates that the
command buffer is empty so that a new command sequence can be executed when performing burst
programming. The FCBEF bit is cleared by writing a one to it or when a burst program command is transferred
to the array for programming. Only burst program commands can be buffered.
0 Command buffer is full (not ready for additional commands).
1 A new burst program command may be written to the command buffer.
FLASH Command Complete Flag — FCCF is set automatically when the command buffer is empty and no
command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to
FCBEF to register a command). Writing to FCCF has no meaning or effect.
0 Command in progress
1 All commands complete
Protection Violation Flag — FPVIOL is set automatically when FCBEF is cleared to register a command that
attempts to erase or program a location in a protected block (the erroneous command is ignored). FPVIOL is
cleared by writing a 1 to FPVIOL.
0 No protection violation.
1 An attempt was made to erase or program a protected location.
Access Error Flag — FACCERR is set automatically when the proper command sequence is not obeyed exactly
(the erroneous command is ignored), if a program or erase operation is attempted before the FCDIV register has
been initialized, or if the MCU enters stop while a command was in progress. For a more detailed discussion of
the exact actions that are considered access errors, see
writing a 1 to FACCERR. Writing a 0 to FACCERR has no meaning or effect.
0 No access error.
1 An access error has occurred.
FLASH Verified as All Blank (erased) Flag — FBLANK is set automatically at the conclusion of a blank check
command if the entire FLASH array was verified to be erased. FBLANK is cleared by clearing FCBEF to write a
new valid command. Writing to FBLANK has no meaning or effect.
0 After a blank check command is completed and FCCF = 1, FBLANK = 0 indicates the FLASH array is not
1 After a blank check command is completed and FCCF = 1, FBLANK = 1 indicates the FLASH array is
0
7
0
completely erased.
completely erased (all 0xFF).
FCMD6
0
6
0
Figure 4-10. FLASH Command Register (FCMD)
Table 4-12. FSTAT Register Field Descriptions
MC9S08AC16 Series Data Sheet, Rev. 8
FCMD5
0
5
0
Execution” for a detailed discussion of FLASH
FCMD4
0
4
0
Description
Section 4.4.5, “Access
FCMD3
3
0
0
FCMD2
0
2
0
Table
Errors.” FACCERR is cleared by
4-14. Refer to
FCMD1
0
1
0
Chapter 4 Memory
FCMD0
0
0
0
61