STM32F205ZFT6 STMicroelectronics, STM32F205ZFT6 Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM32F205ZFT6
Manufacturer Part Number
STM32F205ZFT6
Description
MCU ARM 768KB FLASH 144LQFP
Manufacturer
STMicroelectronics
Series
STM32r
Datasheet
1.STM32F205RBT6.pdf
(163 pages)
Specifications of STM32F205ZFT6
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
120MHz
Connectivity
CAN, I²C, IrDA, LIN, MMC, SPI, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
Number Of I /o
114
Program Memory Size
768KB (768K x 8)
Program Memory Type
FLASH
Eeprom Size
-
Ram Size
132K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 24x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LQFP
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
497-11165
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM32F205ZFT6
Manufacturer:
STMicroelectronics
Quantity:
364
Company:
Part Number:
STM32F205ZFT6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F205ZFT6
Manufacturer:
ST
Quantity:
20 000
Description
2.2.17
a.
22/163
Voltage regulator
The regulator has five operating modes:
●
●
Regulator ON
The regulator ON modes are activated by default on LQFP packages.On WLCSP66
package, they are activated by connecting both REGOFF and IRROFF pins to V
only REGOFF must be connected to V
V
There are three regulator ON modes:
●
●
●
Regulator OFF
●
V
temperature range.
DD
DD
/V
minimum value is 1.8 V
Regulator ON
–
–
–
Regulator OFF
–
–
MR is used in nominal regulation mode (Run)
LPR is used in Stop mode
Power-down is used in Standby mode:
The regulator output is in high impedance: the kernel circuitry is powered down,
inducing zero consumption (but the contents of the registers and SRAM are lost).
Regulator OFF/internal reset ON
On WLCSP66 package, this mode is activated by connecting REGOFF pin to V
IRROFF pin to V
(IRROFF not available).
The regulator OFF/internal reset ON mode allows to supply externally a 1.2 V voltage
source through V
The following conditions must be respected:
–
–
DDA
Main regulator mode (MR)
Low power regulator (LPR)
Power-down
Regulator OFF/internal reset ON
Regulator OFF/internal reset OFF
V
between power domains.
If the time for V
reach 1.8 V
minimum value of 1.65 V is obtained when the device operates in a reduced
DD
should always be higher than V
(a)
SS
CAP_1
, then PA0 should be connected to the NRST pin (see
. On UFBGA176 package, only REGOFF must be connected to V
CAP_1
(a)
and V
.
Doc ID 15818 Rev 6
and V
CAP_2
CAP_2
SS
pins, in addition to V
on UFBGA176 package (IRROFF is not available).
to reach 1.08 V is faster than the time for V
CAP_1
and V
CAP_2
STM32F205xx, STM32F207xx
DD
.
to avoid current injection
Figure
SS
, while
DD
6).
DD
and
DD
to