IDT5T905PGI IDT, Integrated Device Technology Inc, IDT5T905PGI Datasheet - Page 5

• Manufacturer Part Number: IDT5T905PGI
• Description: IC CLK BUFFER 1:5 SGL 28-TSSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Fanout Buffer (Distribution)r

Specifications of IDT5T905PGI

• Number Of Circuits: 1
• Ratio - Input:output: 1:5
• Differential - Input:output: Yes/No
• Input: eHSTL, HSTL, LVPECL, LVTTL
• Output: eHSTL, HSTL, LVTTL
• Frequency - Max: 250MHz
• Voltage - Supply: 2.4 V ~ 2.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP
• Frequency-max: 250MHz
• Number Of Outputs: 5
• Operating Supply Voltage (max): 2.6V
• Operating Temp Range: -40C to 85C
• Propagation Delay Time: 3.5ns
• Operating Supply Voltage (min): 2.4V
• Mounting: Surface Mount
• Pin Count: 28
• Operating Supply Voltage (typ): 2.5V
• Package Type: TSSOP
• Quiescent Current: 30mA
• Duty Cycle: 60%
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 5T905PGI

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR HSTL
NOTES:
1. See RECOMMENDED OPERATING RANGE table.
2. V
3. V
4. For single-ended operation, in differential mode, A/V
5. Voltage required to maintain a logic HIGH, single-ended operation in differential mode.
6. Voltage required to maintain a logic LOW, single-ended operation in differential mode.
7. Typical values are at V
8. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. The correct input interface table should be
9. For differential mode (RxS = LOW), A and A/V
POWER SUPPLY CHARACTERISTICS FOR HSTL OUTPUTS
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations.
2. The termination resistors are excluded from these measurements.
3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH.
IDT5T905
2.5V SINGLE DATA RATE 1:5 CLOCK BUFFER TERABUFFER
Input Characteristics
Output Characteristics
Symbol
only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching
to a new state.
referenced.
Symbol
DIF
CM
I
I
I
V
V
I
DDQQ
I
DDDQ
V
V
V
I
TOTQ
V
V
V
V
DDQ
DDD
TOT
I
I
REF
DIF
IH
CM
OH
IL
OL
IK
IN
IH
IL
specifies the minimum input differential voltage (V
specifies the maximum allowable range of (V
Quiescent V
Quiescent V
Dynamic V
Current per Output
Dynamic V
Current per Output
Total Power V
Total Power V
Input HIGH Current
Input LOW Current
Clamp Diode Voltage
DC Input Voltage
DC Differential Voltage
DC Common Mode Input Voltage
DC Input HIGH
DC Input LOW
Single-Ended Reference Voltage
Output HIGH Voltage
Output LOW Voltage
DD
= 2.5V, V
Parameter
DD
DDQ
Parameter
DD
DDQ
DD
DDQ
Power Supply
(4,6,8)
Power Supply Current
Power Supply
(4,5,8)
Power Supply Current
Supply Current
Supply Current
(9)
(9)
DDQ
(2,8)
= 1.5V, +25°C ambient.
REF
(4,8)
(3,8)
TR
must be at the opposite rail.
REF
+ V
TR
is tied to the DC voltage V
- V
CP
) /2. Differential mode only.
CP
) required for switching where V
V
Outputs enabled, All outputs unloaded
V
Outputs enabled, All outputs unloaded
V
V
V
V
V
V
V
V
V
I
I
I
I
OH
OH
OL
OL
DDQ
DDQ
DD
DD
DDQ
DDQ
DDQ
DDQ
DD
DD
DD
= 8mA
= 100μA
= -8mA
= -100μA
= 2.6V
= 2.6V
= 2.4V, I
= Max., V
= Max., V
= Max., Reference Clock = LOW
= Max., Reference Clock = LOW
= 1.5V, F
= 1.5V, F
= 1.5V, F
= 1.5V, F
Test Conditions
Test Conditions
IN
DDQ
DDQ
REFERENCE CLOCK
REFERENCE CLOCK
REFERENCE CLOCK
REFERENCE CLOCK
= -18mA
REF
5
= Max., C
= Max., C
.
V
V
I
I
= V
= GND/V
(2)
TR
is the "true" input level and V
L
L
DDQ
= 0pF
= 0pF
= 100MHz, C
= 250MHz, C
= 100MHz, C
= 250MHz, C
/GND
DDQ
(3)
(3)
L
L
L
L
= 15pF
= 15pF
= 15pF
= 15pF
V
V
V
REF
DDQ
DDQ
Min.
- 0.3
680
0.2
—
—
—
—
—
—
—
+ 100
- 0.1
- 0.4
CP
INDUSTRIAL TEMPERATURE RANGE
is the "complement" input level. Differential mode
(1)
Typ.
Typ.
- 0.7
750
750
0.1
20
10
15
20
25
15
30
—
—
(7)
V
REF
- 1.2
+3.6
Max
Max
900
0.3
±5
±5
0.4
0.1
30
20
30
30
40
30
60
—
—
—
—
—
- 100
μA/MHz
μA/MHz
(1)
Unit
Unit
mV
mV
mV
mV
mA
mA
mA
mA
μA
V
V
V
V
V
V
V