SI5321-G-BC Silicon Laboratories Inc, SI5321-G-BC Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI5321-G-BC
Manufacturer Part Number
SI5321-G-BC
Description
IC PREC CLOCK MULTIPLIER 63CBGA
Manufacturer
Silicon Laboratories Inc
Type
Clock Multiplierr
Datasheet
1.SI5321-H-GL.pdf
(34 pages)
Specifications of SI5321-G-BC
Package / Case
63-CBGA
Pll
Yes
Input
LVTTL
Output
CML
Number Of Circuits
1
Ratio - Input:output
1:1
Differential - Input:output
Yes/Yes
Frequency - Max
2.8GHz
Divider/multiplier
Yes/Yes
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-20°C ~ 85°C
Mounting Type
Surface Mount
Frequency-max
2.4GHz
Mounting Style
SMD/SMT
Description/function
The is a precision clock multiplier designed to exceed the requirements of high speed communication systems
Operating Supply Voltage
3.3 V
Operating Temperature Range
- 55 C to + 150 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
336-1274
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI5321-G-BC
Manufacturer:
SILICON
Quantity:
5
Company:
Part Number:
SI5321-G-BC
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
SI5321-G-BC
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
and setting FEC[2:0] = 001 (255/238 FEC scaling).
Finally, a 622.08 MHz output clock (a non-FEC rate) can
be generated from a 20.83 MHz input clock (an FEC
rate) by setting INFRQSEL[2:0] = 001 (19.44 MHz
range), setting FRQSEL[2:0] = 011 (32x multiplication)
and setting FEC[2:0] = 010 (238/255 FEC scaling).
2.3. PLL Performance
The
generation, high jitter tolerance, and a well-controlled
jitter transfer function with low peaking and a high
degree of jitter attenuation.
2.3.1. Jitter Generation
Jitter generation is defined as the amount of jitter
produced at the output of the device with a jitter free
input clock. Generated jitter arises from sources within
the VCO and other PLL components. Jitter generation is
a function of the PLL bandwidth setting. Higher loop
bandwidth settings may result in lower jitter generation
but may also result in less attenuation of jitter than
might be present on the input clock signal.
2.3.2. Jitter Transfer
Jitter transfer is defined as the ratio of output signal jitter
to input signal jitter for a specified jitter frequency. The
jitter transfer characteristic determines the amount of
input clock jitter that passes to the outputs. The DSPLL
technology used in the Si5321 provides tightly-
controlled jitter transfer curves because the PLL gain
parameters are determined by digital circuits that do not
vary over supply voltage, process, and temperature. In
a system application, a well-controlled transfer curve
minimizes the output clock jitter variation from board to
board and provides more consistent system level jitter
performance.
The jitter transfer characteristic is a function of the
BWSEL[1:0] setting. Lower bandwidth settings result in
more jitter attenuation of the incoming clock but may
result in higher jitter generation. Table 4 on page 10
gives the 3 dB bandwidth and peaking values for
specified BWSEL settings. Figure 6 shows the jitter
transfer curve mask.
Si5321
PLL
provides
extremely
low
jitter
Rev. 2.5
.
2.3.3. Jitter Tolerance
Jitter tolerance for the Si5321 is defined as the
maximum peak-to-peak sinusoidal jitter that can be
present on the incoming clock. The tolerance is a
function of the jitter frequency because tolerance
improves for lower input jitter frequency.
2.4. Loss-of-Signal Alarm
The Si5321 has loss-of-signal (LOS) circuitry that
constantly monitors the CLKIN input clock for missing
pulses. The LOS circuitry sets a LOS output alarm
signal when missing pulses are detected.
The LOS circuitry operates as follows. Regardless of
the selected input clock frequency range, the LOS
circuitry divides down the input clock into the 19 MHz
range. The LOS circuitry then over-samples this divided
down input clock to search for extended periods of time
without input clock transitions. If the LOS circuitry
detects four consecutive samples of the divided down
input clock that are the same state (i.e., 1111 or 0000), a
LOS condition is declared; the Si5321 goes into digital
hold mode, and the LOS output alarm signal is set high.
The LOS sampling circuitry runs at a frequency of f
where f
FRQSEL[2:0] pins are set to 100. Figure 3 on page 5
and Table 3 on page 7 list the minimum and maximum
transitionless time periods required for declaring a LOS
on the input clock (t
Am plitude
Jitter Out
10 ns
Jitter In
Figure 6. PLL Jitter Transfer Mask/Template
Input
Jitter
Figure 7. Jitter Tolerance Mask/Template
Transfer
Jitter
0 dB
O_78
(s)
–20 dB/dec.
is the output clock frequency when the
J
p
LOS
Peaking
).
Excessive Input Jitter Range
F
BW
F
BW
–20 dB/dec.
Si5321
f
Jitter In
O_78
f
Jitter
19
,