LTC1292DCN8#PBF Linear Technology, LTC1292DCN8#PBF Datasheet - Page 6

• Manufacturer Part Number: LTC1292DCN8#PBF
• Description: IC DATA ACQ SYSTEM 12BIT 8-DIP
• Manufacturer: Linear Technology
• Type: Data Acquisition System (DAS)r

Specifications of LTC1292DCN8#PBF

• Resolution (bits): 12 b
• Sampling Rate (per Second): 60k
• Data Interface: Serial, Parallel
• Voltage Supply Source: Single Supply
• Voltage - Supply: 5V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 60KSPS
• Input Polarity: Unipolar
• Input Type: Voltage
• Rated Input Volt: 5V
• Differential Input: Yes
• Power Supply Requirement: Single
• Single Supply Voltage (typ): 5V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 500mW
• Integral Nonlinearity Error: ±0.75LSB
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 8
• Package Type: PDIP N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LTC1292/LTC1297
TYPICAL PERFOR
PI FU CTIO S
CS (Pin 1): Chip Select Input. A logic low on this input
enables the LTC1292/LTC1297. Power shutdown is acti-
vated on the LTC1297 when CS is brought high.
+IN, –IN (Pin 2, 3): Analog Inputs. These inputs must be
free of noise with respect to GND.
GND (Pin 4): Analog Ground. GND should be tied directly
to an analog ground plane.
V
the span of the A/D converter and must be kept free of
noise with respect to GND.
6
REF
1000
600
900
800
700
500
400
300
200
100
1.0
0.6
0.4
0.2
0.8
U
0
0
100
–50
(Pin 5): Reference Input. The reference input defines
Input Channel Leakage Current vs
Temperature
Maximum Clock Rate vs
Source Resistance
–30
U
–10
AMBIENT TEMPERATURE ( C)
1k
10
R
SOURCE
30
OFF CHANNEL
U
50
– ( )
R
+V
SOURCE
IN
ON CHANNEL
GUARANTEED
10k
70
V
V
CLK = 1MHz
CC
REF
W
–
+
90 110
LTC1292/7 G16
LTC1292/7G13
= 5V
+IN
–IN
= 5V
A
U
100k
130
CE
C
HARA TERISTICS
100
10k
2.25
2.00
1.75
1.50
1.25
1.00
0.50
0.75
0.25
1k
10
1
0
10
Maximum Filter Resistor vs
Cycle Time
Noise Error vs Reference Voltage
0
LTC1292/LTC1297
NOISE = 200 V
C
FILTER
+V
IN
C
1
R
REFERENCE VOLTAGE (V)
FILTER
1 F
100
CYCLE TIME ( s)
P-P
2
D
result is shifted out of this output.
CLK (Pin 7): Shift Clock. This clock synchronizes the serial
data transfer.
V
of noise and ripple by bypassing directly to the analog
ground plane.
+
–
CC
OUT
3
(Pin 8): Positive Supply. This supply must be kept free
1k
(Pin 6): Digital Data Output. The A/D conversion
LTC1292/7 G14
4
LTC1292/7 G17
10k
5
100
** MAXIMUM R
10
* MAXIMUM CLK FREQUENCY REPRESENTS THE
1
100
Sample-and-Hold Acquisition
Time vs Source Resistance
CLK FREQUENCY AT WHICH A 0.1LSB SHIFT IN
THE ERROR AT ANY CODE TRANSITION FROM ITS
1MHz VALUE IS FIRST DETECTED.
RESISTOR VALUE AT WHICH A 0.1LSB CHANGE IN
FULL SCALE ERROR FROM ITS VALUE AT
R
FILTER
V
V
T
0V TO 5V INPUT STEP
REF
CC
A
= 25 C
= 5V
= 0 IS FIRST DETECTED.
= 5V
+V
IN
FILTER
R
SOURCE
R
REPRESENTS THE FILTER
SOURCE
1000
+
–
+ ( )
LTC1292/7 G15
12927fb
10000