ISL90726UIE627Z-TK Intersil, ISL90726UIE627Z-TK Datasheet - Page 3

• Manufacturer Part Number: ISL90726UIE627Z-TK
• Description: IC POT DGTL 50K OHM SC70-6
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of ISL90726UIE627Z-TK

• Taps: 128
• Resistance (ohms): 50K
• Number Of Circuits: 1
• Temperature Coefficient: 45 ppm/°C Typical
• Memory Type: Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SC-70-6, SC-88, SOT-363
• Resistance In Ohms: 50K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ISL90726UIE627Z-TKTR

Absolute Maximum Ratings
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
V
Voltage at any DCP Pin with
I
Latchup . . . . . . . . . . . . . . . . . . . . . . . . . . Class II, Level B at +85°C
ESD Rating
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
Analog Specifications
Operating Specifications
W
RESISTOR MODE
1. θ
R
CC
t
with Respect to V
Respect to V
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2kV
DCP
(Notes 8, 9)
DNL
(10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
C
V
SYMBOL
R
SYMBOL
I
(Note 7)
(Note 5)
R
I
H
CC
LkgDCP
ComLkg
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7V
OFFSET
JA
TOTAL
R
/C
TC
I
R
CC1
I
(Note 9)
(Note 6) Differential Non-linearity
SB
INL
Ramp
W
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
L
R
/C
W
SS
R
R
Wiper Resistance
Potentiometer Capacitance
Leakage on DCP Pins
Integral Non-linearity
Offset
Resistance Temperature
Coefficient
V
(Volatile Write/Read)
V
Common-Mode Leakage
DCP Wiper Response Time
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V
H
H
CC
CC
CC
SS
to R
to R
. . . . . . . . . . . . . . . . . . . . . -0.3V to V
Supply Current
Current (Standby)
Ramp Rate
L
L
PARAMETER
Resistance Tolerance
PARAMETER
Resistance
Over recommended operating conditions unless otherwise stated.
3
W, U versions respectively
V
Voltage at pin from GND to V
DCP register set between 20 hex and 7F hex.
Monotonic over all tap positions (Note 3)
DCP register set between 20 hex
and 7F hex. Monotonic over all tap
positions (Note 3)
W option
U option
DCP register set between 20 hex and 7F hex
(Note 3)
CC
f
Read and Volatile Write States only)
V
Voltage at SDA pin at GND or V
SCL falling edge of last bit of DCP Data Byte to
wiper change
SCL
CC
= 3.3V @ +25°C
= +5.5V, I
= 400kHz; SDA = Open; (for I
CC
+ 0.3
TEST CONDITIONS
CC
TEST CONDITIONS
ISL90726
2
C Interface in Standby State
Thermal Information
Thermal Resistance (Typical, Note 1)
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
Recommended Operating Conditions
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
V
Power rating of each DCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
CC
CC
6 Ld SC-70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
CC
2
W option
U option
C, Active,
(Note 12)
(Note 12)
MIN
-20
-2
-1
-1
0
0
MIN
0.2
10/10/25
(Note 2)
10, 50
±0.25
TYP
±0.1
±0.1
±45
0.1
(Note 2)
0.5
85
1
TYP
500
(Note 12)
MAX
+20
(Note 12) UNIT
1
2
1
1
3
2
MAX
200
500
3
August 26, 2008
θ
JA
(Note 4)
(Note 4)
(Note 4)
(Note 4)
(Note 4)
ppm/°C
590
UNIT
FN8244.4
(°C/W)
kΩ
µA
pF
MI
MI
MI
MI
MI
V/ms
%
Ω
µA
µA
nA
ns