MT46H16M16LFBF-6:A Micron Technology Inc, MT46H16M16LFBF-6:A Datasheet - Page 26

• Manufacturer Part Number: MT46H16M16LFBF-6:A
• Manufacturer: Micron Technology Inc
• Type: DDR SDRAMr

Specifications of MT46H16M16LFBF-6:A

• Organization: 16Mx16
• Density: 256Mb
• Address Bus: 15b
• Access Time (max): 6.5/5ns
• Maximum Clock Rate: 166MHz
• Operating Supply Voltage (typ): 1.8V
• Package Type: VFBGA
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 1.95V
• Operating Supply Voltage (min): 1.7V
• Supply Current: 100mA
• Pin Count: 60
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / Rohs Status: Compliant

Table 9: Electrical Characteristics and Recommended AC Operating Conditions (Continued)
Notes 1–9 apply to all parameters in this table; V
PDF: 09005aef834bf85b
256mb_mobile_ddr_sdram_t36n.pdf - Rev. H 11/09 EN
Parameter
DQS read
preamble
DQS read postamble
Active bank a to active bank
b command
Read of SRR to next valid
command
SRR to read
DQS write preamble
DQS write preamble setup
time
DQS write postamble
Write recovery time
Internal WRITE-to-READ
command delay
Exit power-down mode to
first valid command
Exit self refresh to first valid
command
CL = 2
Notes:
Symbol
t
1. All voltages referenced to V
2. All parameters assume proper device initialization.
3. Tests for AC timing and electrical AC and DC characteristics may be conducted at nomi-
4. The circuit shown below represents the timing reference load used in defining the rele-
5. The CK/CK# input reference voltage level (for timing referenced to CK/CK#) is the point
t
WPRES
t
t
t
WPRE
t
WPST
t
RPRE
t
t
t
RPST
t
WTR
RRD
t
SRC
SRR
XSR
WR
XP
nal supply voltage levels, but the related specifications and device operation are guaran-
teed for the full voltage ranges specified.
vant timing parameters of the device. It is not intended to be either a precise representa-
tion of the typical system environment or a depiction of the actual load presented by a
production tester. System designers will use IBIS or other simulation tools to correlate
the timing reference load to system environment. Specifications are correlated to produc-
tion test conditions (generally a coaxial transmission line terminated at the tester elec-
tronics). For the half-strength driver with a nominal 10pF load, parameters
are expected to be in the same range. However, these parameters are not subject to
production test but are estimated by design/characterization. Use of IBIS or other simula-
tion tools for system design validation is suggested.
at which CK and CK# cross; the input reference voltage level for signals other than CK/
CK# is V
I/O
Full drive strength
CL + 1
Min
0.25
DDQ
0.5
0.4
0.4
10
15
80
2
0
1
1
50
/2.
-5
Electrical Specifications – AC Operating Conditions
DD
Max
/V
1.1
0.6
0.6
–
–
–
–
–
–
–
–
–
DDQ
20pF
= 1.70–1.95V
CL + 1
Min
10.8
0.25
0.5
0.4
0.4
15
80
26
2
0
1
1
SS
-54
.
I/O
256Mb: x16, x32 Mobile LPDDR SDRAM
Max
1.1
0.6
0.6
Half drive strength
–
–
–
–
–
–
–
–
–
Micron Technology, Inc. reserves the right to change products or specifications without notice.
50
CL + 1
Min
0.25
0.5
0.4
0.4
12
15
80
2
0
1
1
-6
Max
1.1
0.6
0.6
10pF
–
–
–
–
–
–
–
–
–
CL + 1
Min
0.25
0.5
0.4
0.4
15
15
80
2
0
1
1
©2008 Micron Technology, Inc. All rights reserved.
-75
Max
1.1
0.6
0.6
–
–
–
–
–
–
–
–
–
Unit
t
t
t
t
t
t
t
t
t
ns
ns
ns
ns
CK
CK
CK
CK
CK
CK
CK
CK
AC and
Notes
24, 25
26
27
28
t
QH